manualshive.com logo in svg

Philips M3000A, Service Manual

The Yamaha M3000A Owner's Manual is a comprehensive guide for operating and maximizing the potential of the Yamaha M3000A mixer. This manual is available for free download at manualshive.com, offering users easy access to essential instructions and insights on this top-of-the-line audio equipment.

Share
Download
background image

Monitor Theory of Operation

Introduction to the Instrument

 

13

Display and User Interface Software Module

The Display and User Interface Software displays measurement data and status information 
on the color LCD display, and processes the operator inputs from the HIF Controller. The 
interface consists of the following sub-modules:

• Screen Configuration.
• Numerics and Wave Presentation.
• Key and TouchStrip Processing.
• Alarm and Status Presentation.

Alarm Manager Software Module

The visual and audible alarms generated by the Measurement Server, the Measurement 
Server Extension or by the Monitor software modules are assigned priorities by the Alarm 
Manager. The Alarm Manager also:

• Monitors the “alarm suspended”, “alarm silence” and “alarm reminder” functionality.
• Manages alarm latching (alarms remain in effect until reset or turned off by the user).
• Triggers the Nurse Call Relay.
• Generates alarm event triggers for any user-defined trigger conditions.

Admit / Discharge / Transfer (ADT) Software Module

This module maintains the patient’s demographics and controls the upload of trend data from 
the Measurement Server and the Measurement Server Extension. It allows the user to:

• Admit a new patient.
• Transfer a patient to another Monitor.
• Discharge a patient.

Trend Software Module

This module manages a trend database. It stores physiological values from the Measurement 
Server and from the Measurement Server Extension in two separate databases, a short-term 
and a long-term database. The contents of these databases is battery-buffered, so that no data 
is lost in the event of a power failure.

Events Software Module

The events software module allows the user to take snapshots of the Monitor state and store 
them for later viewing or printing.This can be done automatically, triggered by alarms, if the 
monitor is configured appropriately. The types of data that can be captured are as follows:

• All physiological values.
• All current alarms.
• The last 20 seconds of wave data.

Summary of Contents for M3000A






































































































































































































































































































Reviews:

No comments

Related manuals for M3000A

Campbell 107 Product Manual preview
107
Brand: Campbell Pages: 25
Larson Davis 820 Quick User Manual preview
820
Brand: Larson Davis Pages: 2
G-Tek 27 Series Operating Manual preview
27 Series
Brand: G-Tek Pages: 27
Kane 3500 Manual preview
3500
Brand: Kane Pages: 20
3M Workstation Monitor 724 Instructions Manual preview
Workstation Monitor 724
Brand: 3M Pages: 21
3M SE-400 Series Getting Started preview
SE-400 Series
Brand: 3M Pages: 2
3M SD-200 Quick Start preview
SD-200
Brand: 3M Pages: 2
3M Dynatel 965AMS User Manual preview
Dynatel 965AMS
Brand: 3M Pages: 24
3M Dynatel 2250M Quick Manual preview
Dynatel 2250M
Brand: 3M Pages: 2
3M SoundPro SE Series Data Addendum Manual preview
SoundPro SE Series
Brand: 3M Pages: 293
Jasco V-530 Hardware/Function Manual preview
V-530
Brand: Jasco Pages: 48
LaserLiner PowerCross-Laser 8 S Operating Instructions Manual preview
PowerCross-Laser 8 S
Brand: LaserLiner Pages: 64
LaserLiner ClimaHome-Check Plus Manual preview
ClimaHome-Check Plus
Brand: LaserLiner Pages: 10
LaserLiner MeterMaster Plus Quick Start Manual preview
MeterMaster Plus
Brand: LaserLiner Pages: 104
LaserLiner ThermoSpot Operating Instructions Manual preview
ThermoSpot
Brand: LaserLiner Pages: 52
LaserLiner LaserRange-Master T2 Manual preview
LaserRange-Master T2
Brand: LaserLiner Pages: 52
LaserLiner ArcoMaster 40 Quick Start Manual preview
ArcoMaster 40
Brand: LaserLiner Pages: 5
LaserLiner CombiRangeXtender 40 Operating Instructions Manual preview
CombiRangeXtender 40
Brand: LaserLiner Pages: 84

Brands by name

Popular brands

Load more brands