manualshive.com logo in svg

Philips M3000A, Service Manual

The Yamaha M3000A Owner's Manual is a comprehensive guide for operating and maximizing the potential of the Yamaha M3000A mixer. This manual is available for free download at manualshive.com, offering users easy access to essential instructions and insights on this top-of-the-line audio equipment.

Share
Download
background image

General Cleaning of the Instrument

Maintaining the Instrument

 

125

Replacement of the Pump and CO

2

 Scrubber

Replacement of the Pump and CO2 Scrubber is supported for units with serial number 
prefix DE020xxxxx only. Where a recommendation is made to replace the Pump and CO

2

 

Scrubber, this applies only to these earlier units. If the Pump and CO

2

 Scrubber are defective 

in later units with serial number prefix DE435xxxxx, repair is effected by M3015A unit 
exchange.

The procedure for replacing the Pump and CO

2

 Scrubber is found in "Repairing the 

Instrument".

The effectiveness of the Pump and the CO

2

 Scrubber gradually decreases over time. As a 

result, periodic replacement is necessary.

Philips recommends replacement as follows:

• After 15,000 hours of use (check “Pump Op Time”. See  “Checking and Resetting Time 

Counters” on page 153).

• If the Instrument requires repairs, check the time counters, and replace the Pump and CO

2

 

Scrubber if necessary, in addition to any other repairs.

NOTE 

After fitting the new part(s), go to Service Mode and reset the counter for the part(s) you have 
replaced. The procedure for resetting the counters is found in "Repairing the Instrument".

When the PumpOpTime has been reset an INOP will be generated: “CO

2

 OCCLUSION”. To 

clear this INOP you must perform a flow check and store the flow in Service Mode (select 
“Store Flow”).

Replacement of the Infrared Lamp

The infrared lamp can be exchanged only in units with serial number prefix DE020xxxxx 
manufactured before June 2002. The support strategy for later units in case of an infrared 
lamp failure is M3015A unit exchange.

General Cleaning of the Instrument

The Monitor, the Measurement Server, and the Measurement Server Extension should be 
kept free of dust and dirt. In particular, exterior cleaning of the Monitor’s case and LCD 
screen is recommended. Clean the case with a lint-free cloth or sponge, moistened with either 
soap and water, a diluted non-caustic detergent or one of the cleaning agents listed in this 
chapter. Universal Display Cleaner or window cleaner is recommended for the cleaning of 
the LCD screen.

Full cleaning instructions are given in the Instructions for Use.

Cleaning Guidelines

To avoid damage to the Instrument, follow these cautionary guidelines:

Summary of Contents for M3000A






































































































































































































































































































Reviews:

No comments

Related manuals for M3000A

PAT DS 150 Service Manual preview
DS 150
Brand: PAT Pages: 55
PAT DS 150 User Manual preview
DS 150
Brand: PAT Pages: 31
ParTech 8100 Instruction Manual preview
8100
Brand: ParTech Pages: 14
Oldham BM25 Operating Manual preview
BM25
Brand: Oldham Pages: 43
Gardner Bender PM3000 Operating Instructions preview
PM3000
Brand: Gardner Bender Pages: 4
GAPS Clack WS1 Installation, Operation And Maintenance Manual preview
Clack WS1
Brand: GAPS Pages: 36
yellow jacket 68940 Operation Manual preview
68940
Brand: yellow jacket Pages: 26
Han Seung HTS-CT10 Operating Manual preview
HTS-CT10
Brand: Han Seung Pages: 2
Omega DP25B-E User Manual preview
DP25B-E
Brand: Omega Pages: 74
Omega CL1000 Series User Manual preview
CL1000 Series
Brand: Omega Pages: 24
GF Signet FlowtraMag 2580 Series Operating Instructions Manual preview
Signet FlowtraMag 2580 Series
Brand: GF Pages: 20
Ocea Soft Cobalt 2 Installation Manual preview
Cobalt 2
Brand: Ocea Soft Pages: 19
PICO TA167 User Manual preview
TA167
Brand: PICO Pages: 2
FM Marin Gobius 4 Waste Installation Manual preview
Gobius 4 Waste
Brand: FM Marin Pages: 8
ThermoFisher Scientific Thermo Scientific iCE 3000 Series Pre-Installation Manual preview
Thermo Scientific iCE 3000 Series
Brand: ThermoFisher Scientific Pages: 42
Kane KANE451 Manual preview
KANE451
Brand: Kane Pages: 52
AXE MM2 Series Operation Manual preview
MM2 Series
Brand: AXE Pages: 5
BUSCH VACTEST GCD 200 Instruction Manual preview
VACTEST GCD 200
Brand: BUSCH Pages: 12

Brands by name

Popular brands

Load more brands