Philadelphia Scientific BOS-CB6700 Installation Manual Download Page 70

Page: 70 / 84

Philadelphia Scientific

iBOS

Pro 6 Series Installation Manual

Page 70 of 84

8.7 System Trouble Shooting Reference

8.7.1 System Information.

Shows



versions of the software for

both the display and the

control box



Lowest bus voltage



Bus statistics



Last Event



Ethernet Upload Setting

8.7.2 Wireless Display RF
Antenna Relocation



If reception is not good to the

mounted wireless display, an

additional 20’ (6.1 m)

Antenna Extension Cable

(BOS-163) can be purchased

to move the antenna to an

improved reception location.



Once relocated, use the

wireless communications test

to verify location

New Location with direct line of site

System Tip:

Always leave batteries connected to a charger. The charger will automatically

refresh the battery to keep it ready to go, as long as a refresh interval has been set and the

charger is capable of refreshing.

Summary of Contents for BOS-CB6700





















































































Search results

Summary of Contents for BOS-CB6700

Reviews:

Brands by name

Popular brands

Philadelphia Scientific BOS-CB6700, Installation Manual

Search results

Summary of Contents for BOS-CB6700

Reviews:

Brands by name

Popular brands