PEUGEOT Django 125 Workshop Manual Download Page 68

Page: 68 / 83

STEERING/FORK

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Scooters

- Fit the front mudguard.
- Fit the speedometer drive gear assembly to the

wheel drive pins.

- Fit the wheel, matching the speedometer drive

gear assembly to the pin (A) on the fork
stanchion.

- Fit the wheel spindle and tighten.

Tightening torque: 65 Nm.

When re-installing, use a new nut.

- Fit the brake calliper.

• 2 Ø 8 mm screws.

Tightening torque: 30 Nm.

When refitting the brake caliper, spread
standard thread lock on the bolts.

Removal of the fork

- Remove the front mudguard. See: Procedure 17.

page 29.

- Remove the brake caliper without disconnecting

it.

Tightening torque: 30 Nm.

When refitting the brake caliper, spread
standard thread lock on the bolts.

GLUE

Summary of Contents for Django 125




















































































Search results

Summary of Contents for Django 125

Reviews:

Related manuals for Django 125

Brands by name

Popular brands

PEUGEOT Django 125, Workshop Manual

Search results

Summary of Contents for Django 125

Reviews:

Related manuals for Django 125

Brands by name

Popular brands