PEUGEOT Django 125 Workshop Manual Download Page 57

Page: 57 / 83

SERVICE OPERATIONS

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Scooters

Rear brake

When changing the brake pads, it is
essential to replace the brake pad
attachment system (spindle, pin, clips, ...)

- Remove the wheel trim.
- Remove the 5 screws fastening the rear wheel.

Tightening torque: 30 Nm.

- Loosen the brake pad pin first. (1)
- Remove the brake caliper (2 screw).

Tightening torque: 30 Nm.

When refitting the brake caliper, spread
standard thread lock on the bolts.

- Remove the brake pad pin (2).
- Remove the tension spring (3).
- Remove the brake pads (4).

When refitting the brake pads, push the
pistons all the way into their housing.

After refitting, actuate the brake levers
several times to bring the brake pads
against the brake disc.

GLUE

Summary of Contents for Django 125




















































































Search results

Summary of Contents for Django 125

Reviews:

Related manuals for Django 125

Brands by name

Popular brands

PEUGEOT Django 125, Workshop Manual

Search results

Summary of Contents for Django 125

Reviews:

Related manuals for Django 125

Brands by name

Popular brands