PEUGEOT Django 125 Workshop Manual Download Page 62

Page: 62 / 83

STEERING/FORK

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Scooters

STEERING/FORK

Changing the front fork seals

- Remove the front mudguard. See: Procedure 17.

page 29.

- Remove the brake caliper without disconnecting

it.
• 2 Ø 8 mm screw.

When refitting the brake caliper, spread
standard thread lock on the bolts.

- Unscrew and remove the 2 upper screws (1) from

the fork Tee.

- Before, loosen the fork tube caps (A).
- Unscrew the 2 lower screws (2) from the fork

Tee.

- Remove the fork stanchions.

- Remove the fork tube cap (A).

Check the condition of the O-rings (B).

- Remove the spring (C).

- Drain the front fork. See chapter : Draining the

front fork, page 60.

GLUE

Summary of Contents for Django 125




















































































Search results

Summary of Contents for Django 125

Reviews:

Related manuals for Django 125

Brands by name

Popular brands

PEUGEOT Django 125, Workshop Manual

Search results

Summary of Contents for Django 125

Reviews:

Related manuals for Django 125

Brands by name

Popular brands