PEUGEOT Django 125 Workshop Manual Download Page 56

Page: 56 / 83

SERVICE OPERATIONS

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Scooters

Rear brake

- If one of the 2 brake pads is worn down to the

minimum dimensions (A), the 2 brake pads must
be changed.

A. Mini. thickness: 1.5 mm.

Replacing the brake pads

Front brake

- Remove the caps (1) on the brake pad pins.
- Loosen the brake pad pins beforehand.

Tightening torque: 10 Nm.

- Remove the calliper (2 screw).

Tightening torque: 30 Nm.

When refitting the brake caliper, spread
standard thread lock on the bolts.

When changing the brake pads, it is
essential to replace the brake pad
attachment system (spindle, pin, clips, ...)

- Remove the 2 spindles from the brake pads (2).
- Remove the brake pads (3).

When refitting the brake pads, push the
pistons all the way into their housing.

After refitting, actuate the brake levers
several times to bring the brake pads
against the brake disc.

A = 1.5mm

GLUE

Summary of Contents for Django 125




















































































Search results

Summary of Contents for Django 125

Reviews:

Related manuals for Django 125

Brands by name

Popular brands

PEUGEOT Django 125, Workshop Manual

Search results

Summary of Contents for Django 125

Reviews:

Related manuals for Django 125

Brands by name

Popular brands