PEUGEOT Django 125 Workshop Manual Download Page 77

Page: 77 / 83

ELECTRICITY

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Scooters

Checking the carburettor heating circuit

Power supply range of the carburettor heating

resistor:

between 10±2 and 20±2 °C.

Disconnect the temperature control unit and

take the measurements on the harness side.

- Between the green wire and the ground: 0

Ω

- Between the white/yellow wire and the ground

(Resistor warming carburator):9.5

Ω

±20%

- Between the black wire and the ground, ignition

on: 12V (Battery voltage).

- Between the yellow wire and the ground, engine

running: 13.5V (Regulated alternating current).

If the values are correct, replace the

temperature control unit.

If the values are incorrect, check:

• The harness.
• The ignition switch.
• The carburettor heating resistor : 9.5

Ω

±20%

Checking the starter circuit.

Checking the starter resistance:

- Disconnect the limiting resistance.
- Measure the value of the resistance between

the resistor wire and the earth: 5

Ω

±20%

Checking the electric starter

- Removal of the electric choke.
- Connect the starter to a battery. The starter

piston should retract.

Ω

Summary of Contents for Django 125




















































































Search results

Summary of Contents for Django 125

Reviews:

Related manuals for Django 125

Brands by name

Popular brands

PEUGEOT Django 125, Workshop Manual

Search results

Summary of Contents for Django 125

Reviews:

Related manuals for Django 125

Brands by name

Popular brands