PEUGEOT Django 125 Workshop Manual Download Page 27

Page: 27 / 83

BODY PANELS

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Scooters

Removal of the speedometer fairing

Procedure 11.

- Remove the headlight fairing. See:

Procedure 10.

page 25.

- Disconnect:

• The instrument panel.
• The control clusters.
• The brake light switches

- Remove the speedometer fairing.

• 4 plastic screws.

Removal of the footboard

Procedure 12.

- Remove the upper side fairings. See:

Procedure 6. page 21.

- Remove the storage compartment. See:

Procedure 2. page 20.

- Remove the bracket and the driver's saddle (1).

• 2 washer head screws.

• 2 Ø8 mm screw

- Remove the central fairing bracket under the

saddle (2).

• 2 Ø5 mm screw

- Remove the 3 footboard mats (3).

Summary of Contents for Django 125




















































































Search results

Summary of Contents for Django 125

Reviews:

Related manuals for Django 125

Brands by name

Popular brands

PEUGEOT Django 125, Workshop Manual

Search results

Summary of Contents for Django 125

Reviews:

Related manuals for Django 125

Brands by name

Popular brands