Command
Parameter
^ADxxxxxx
Selects the 9490 printer whose ASCII address is xxxxxx.
^CA
Cancels all the batches in the queue.
^CB
Cancels only the current batch being printed.
^DD or
^DCd
Disables the MPCL data escape character (the tilde) and inhibits
MPCL from acting on ANY data escape sequence from the host. Sets
the MPCL data escape character to the ASCII value given by the
d
parameter. The value can be any ASCII character.
^EA
Aborts an error condition. May need to be sent multiple times. Use
^RB to reprint batch.
CAUTION:
Command causes the current batch
to stop and the condition that caused the error to remain uncorrected.
^ER
Resets the error. This command is the same as pressing the trigger or
pressing
E
to acknowledge an error. Normal operation will resume.
^FD
Feeds a label when printer is
idle
. Simulates the operation of
pressing trigger or
f
and dispenses the next label if printer is in the
on demand mode.
NOTE:
Printer ignores this command if printing.
^ID or ^ICd
Disables the Immediate Command feature by turning off the Immediate
Command escape character. Sets the Immediate Command escape
character to the ASCII value given by the
d
parameter. The value can
be any ASCII character.
^MC
Returns the customer ID or RPQ version to the host. (
00
to
99
)
^MI
Returns the customer ID or RPQ revision level to the host. (
00
to
99
)
^MM
Returns the model number to the host. 00 = M9446 01 =
M1446/M1460
02= M9490 04= M9494
^MP
Returns the prototype number to the host. (
00
to
99
)
^MR
Returns the revision number to the host. (
00
to
99
)
^MV
Returns the version number to the host. (
00
to
99
)
^PR
Resets the printer. This command takes five seconds to complete and
then the printer is ready to receive data. It has the same effect as
turning off and then turning on the printer.
NOTE:
Command should
be used only when the printer is
not
printing.
^RB
Repeats the last printed batch, printing the same number of labels as
specified in the original batch. This command does not work if using
batch separators.
NOTE:
Printer ignores this command if printing.
^RS
Resynchronizes supply when supply roll is changed.
NOTE:
Printer
ignores this command if printing.
^SD or
^SCd
Disables the status polling feature by turning off the status polling
control character. Sets the status polling control character to the
ASCII value given by the
d
parameter. The value of
d
can be any
ASCII character.
^TP
Prints a test label set.
NOTE:
Printer ignores this command if printing.
The table represents the defined immediate command control character as
^
and the
defined status polling control character as
d
. You may define these characters to suit
your needs.
MPCLII Packet Reference Manual
3-24
Summary of Contents for Monarch 1460
