![background image](http://html1.mh-extra.com/html/patton/1000/1000_getting-started-manual_4020433046.webp)
1 • General Information
SmartNode 1000 and 2000 Series Getting Started Guide
46
Interface cards descriptions
Jumper settings for IC-4BRV-8V. The jumpers for each port are located behind the port connector
(see
figure 25
):
Figure 25. Jumpers
Port jumpers can configured as shown in
table 17
.
IC-4BRV-8VR—8-channel gateway interface card for ISDN BRI with hardware
bypass (emergency) relay
The IC-4BRV-8VR is a PMC standard compatible interface card for the SmartNode 2000 series. It provides 4
ISDN BRI interfaces and connects through a PCI packet and PCM circuit interface to the SmartNode base
unit.
The specifications for the IC-4BRV-8VR are identical with the IC-4BRV-8V (see section “
“IC-4BRV-8V 8-
channel gateway interface card for ISDN BRI”
on page 43), with an additional hardware bypass (emergency)
relay. The relay works as follows: If a power failure occurs, the relay connects the interfaces BRI1 and BRI 2
with each other. For this to work as expected:
•
BRI 1 must be connected to a telephone terminal or PBX
•
BRI 2 must be connected to the ISDN network
Table 17. Jumper configurations
No jumpers are set. In this configuration, no line power is fed to port. Use this setting for
USR
ports when connected to an ISDN NT.
Normal feeding. Use this setting when the port is configured as
NET and a line-powered termi-
nal is attached.
Inverse feeding. Same function as in normal feeding, except that the polarity is inverted
(required in some countries, Japan, for example).
3
2
1
0
40V
40V
40V
40V
Summary of Contents for 1000
