![background image](http://html1.mh-extra.com/html/patton/1000/1000_getting-started-manual_4020433028.webp)
1 • General Information
SmartNode 1000 and 2000 Series Getting Started Guide
28
SmartNode 2300 description
Note
The SmartNode 1400 needs to be rebooted twice after changing the
clock mode.
In addition, two other elements—the Reset button and power input socket—are available on the rear panel of a
SmartNode 1200 as described in
table 8
.
SmartNode 2300 description
The SmartNode Model 2300 (see
figure 8
) is a powerful multi-service access device. The 19-in. aluminum
chassis can be rack-mounted and it provides three expansion slots for interface cards.
Note
If you will be mounting the SmartNode 2300 in a 19-in. rack, see
section
“Mounting the SmartNode 2300”
on page 93 for details.
Slave (User)
Master (Net) Port 0. Clock is taken from port 0 if available. Otherwise it is generated inter-
nally.
Master (Net) Slave (User)
Not supported
Table 8. SmartNode 1200 Reset button and power line socket on rear panel
Element
Description
Reset button
The button has three different functions:
•
Manual Restart—
During normal operation pressing and releasing the reset button
will cause a system reboot. The application will be restarted without any change to the
existing SmartWare configuration.
•
Restoration—
Pressing and holding the reset button for 5 seconds will restore the fac-
tory configuration and automatically reboot the system.
Note
In this case the existing IP SmartWare configuration is lost.
•
Boot loader—
Powering the SmartNode while pressing the reset button for 5 seconds
will cause the factory-fitted boot loader to start in place of the application. The boot
loader uses a minimal set of parameters. In case the application does not start correctly,
the boot loader can be used as a fallback to download a new software version.
100–240 VAC
50/60 Hz
Electricity supply socket for mains power cable.
Table 7. Clock-modes and clock-sources for the SmartNode 1400
Port 0
Clock Mode
Port 1
Clock Mode
Clock Source
Summary of Contents for 1000
