Paradyne Hotwire 8776 User Manual Download

Page: 70 / 112

7. Security

7-2

February 2001

8776-A2-GB20-40

Creating a Login

Logins apply to Telnet access to the unit’s ATI. The Administer Logins menu is not
presented when you access the unit through the MCC.

Six login ID/password combinations are available. Each Login ID and Password
must be unique and include an access level.

Procedure

1. To create a login record, follow this menu selection sequence:

Main Menu

→

Control

→

Administer Logins

2. Select New and press Enter. The Login Entry screen is displayed.

main/control/admin_logins Hotwire

Slot: 4

Model: 8776

ADMINISTER LOGINS Page 1 of 1

Login ID: newuser

Access Level: Administrator

Are You Sure? Yes

--------------------------------------------------------------------------------

ESC for previous menu MainMenu Exit

Save PgUp PgDn New Delete

main/control/admin_logins Hotwire

Slot: 4

Model: 8776

LOGIN ENTRY

Login ID: newuser

Password: e34t136

Re-enter Password: e34t136

Access Level: Administrator

WARNING

New logins will not become permanent until saved

through the “ADMINISTER LOGINS” screen!

--------------------------------------------------------------------------------

Ctrl-a to access these functions ESC for previous menu MainMenu Exit

Save PgUp PgDn New Delete

Summary of Contents for Hotwire 8776

















































































































Search results

Summary of Contents for Hotwire 8776

Reviews:

Related manuals for Hotwire 8776

Brands by name

Popular brands

Paradyne Hotwire 8776, User Manual

Search results

Summary of Contents for Hotwire 8776

Reviews:

Related manuals for Hotwire 8776

Brands by name

Popular brands