Paradyne Hotwire 8776 User Manual Download

Page: 56 / 112

5. Testing

5-4

February 2001

8776-A2-GB20-40

G.703 Repeater Loopback

A G.703 Repeater Loopback (RLB) loops the signal being sent from the data port
back to the data port and to the network interface.

Procedure

To run a G.703 Repeater Loopback:

1. Position the cursor at the Start command next to Repeater Loopback on the

Network & G.703 Tests screen.

2. Press Enter.

The Start command is changed to Stop.

3. To manually stop the test, verify that the cursor is positioned at the Stop

command.

4. Press Enter.

The G.703 Repeater Loopback cannot be started when any other loopback
is in progress.

NOTE:

Activating the G.703 Repeater Loopback test causes the Embedded
Operations Channel (EOC), used for management, to be lost to the
remote unit.

CAP

DSL
Port

G.703
Port

CAP

LIU

Framer

Transceiver

98-15999

Summary of Contents for Hotwire 8776

















































































































Search results

Summary of Contents for Hotwire 8776

Reviews:

Related manuals for Hotwire 8776

Brands by name

Popular brands

Paradyne Hotwire 8776, User Manual

Search results

Summary of Contents for Hotwire 8776

Reviews:

Related manuals for Hotwire 8776

Brands by name

Popular brands