Paradyne Hotwire 8776 User Manual Download Page 55

Page: 55 / 112

5. Testing

8776-A2-GB20-40

February 2001

5-3

Network Line Loopback

A Network Line Loopback (LLB) loops the received signal on the network interface
back to the network without change.

Procedure

To run a Network Line Loopback:

1. Position the cursor at the Start command next to Network Line Loopback on

the Network & G.703 Tests screen.

2. Press Enter.

The Start command is changed to Stop.

3. To manually stop the test, verify that the cursor is positioned at the Stop

command.

4. Press Enter.

The Network Line Loopback cannot be started when a Repeater Loopback, DTE
Loopback, or network-initiated Line Loopback is in progress.

CAP

DSL
Port

G.703
Port

CAP

LIU

Framer

Transceiver

AIS

98-15997

Summary of Contents for Hotwire 8776

















































































































Search results

Summary of Contents for Hotwire 8776

Reviews:

Related manuals for Hotwire 8776

Brands by name

Popular brands

Paradyne Hotwire 8776, User Manual

Search results

Summary of Contents for Hotwire 8776

Reviews:

Related manuals for Hotwire 8776

Brands by name

Popular brands