Paradyne Hotwire 8776 User Manual Download

Page: 42 / 112

4. Monitoring the Unit

4-6

February 2001

8776-A2-GB20-40

Performance Statistics

Performance statistics can assist you in determining the duration of specific
conditions and provide a historical context for problem detection and analysis.
Statistics are maintained for up to 96 15-minute intervals (24 hours).

Select a port to view performance statistics for that port. Port 1 is the default.

Use the applicable virtual function keys to page through the intervals and clear
statistics.

Select PgUp or PgDn to view more statistics.

Select ClrNear or ClrFar to clear the near- and far-end statistics to zero.

Select ClrStats to clear all statistics to zero.

Viewing Network Error Statistics

The termination unit maintains error statistics on the network DSL interface for
each port.

To view Network Error Statistics, follow this menu selection sequence:

Main Menu

→

Status

→

Performance Statistics

→

Network Error Statistics

main/status/performance/net_error Hotwire

Slot: 4: Model: 8776

Port: 3 NETWORK ERROR STATISTICS

Current Interval Timer: 2 Error Events Counter: 34

--------------------------------------------------------------------------------

---ES--- ---SES--- --FEBE-- -Complete-

Near Far Near Far Near Far Near Far

Current Int: 000 000 000 000 000 000 Yes Yes

Interval 01 000 000 000 000 000 000 Yes Yes

Interval 02 000 000 000 000 000 000 Yes Yes

Interval 03 000 000 000 000 000 000 Yes Yes

Interval 04 000 000 000 000 000 000 Yes Yes

Interval 05 000 000 000 000 000 000 Yes Yes

Interval 06 000 000 000 000 000 000 Yes Yes

Interval 07 000 000 000 000 000 000 Yes Yes

Worst Interval: 24 09 14 08 18 18

Near Tot(valid): 00010 00000 00000

Far Tot(valid): 00010 00000 00000

--------------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous menu MainMenu Exit

PgUp PgDn ClrNear ClrFar

Summary of Contents for Hotwire 8776

















































































































Search results

Summary of Contents for Hotwire 8776

Reviews:

Related manuals for Hotwire 8776

Brands by name

Popular brands

Paradyne Hotwire 8776, User Manual

Search results

Summary of Contents for Hotwire 8776

Reviews:

Related manuals for Hotwire 8776

Brands by name

Popular brands