21
20
USER MANUAL
MOTORCYCLE SERVICE-SECURITY SYSTEM PANDORA DXL 1200L
EN
mode. Connect the module in accordance with installation manual. The system will confirm the
registration with a short sound signal.
Saving changes:
To finish the recording of the engine compartment module, VALET button should be pressed once
again, the series of red and green flashes of the status LED will confirm the saving, switch on the ignition
to automatically save the settings and exit programming mode.
Levels 6, 7 – Recording Bluetooth radio relays №1, №2
Radio relays recording is performed one by one starting from the 6 level: radio relay №1 is recorded
on the 6 level; radio relay №2 is recorded on the 7 level. The radio relay can be overwritten only on the
level of its initial registration. To record Bluetooth radio relays №1, №2, enter programming mode and
press VALET button 6 times for radio relay №1 or 7 times for radio relay №2. LED indicator will light
green and the system will enter the recording of a radio relay mode. Connect a relay in accordance with
installation manual. The system will confirm recording with a short sound signal.
Saving changes:
To finish the recording of the Bluetooth radio relay, VALET button should be pressed once again, the
series of red and green flashes of the status LED indicator will confirm the saving, switch on the ignition
to automatically save the settings and exit the programming mode.
Level 8 – Recording external Bluetooth GPS/GLONASS receiver
To record an external Bluetooth GPS/GLONASS receiver, enter programming mode and press VALET
button 8 times. The LED indicator will light green and the system will enter the recording of a receiver.
Connect the receiver in accordance with its installation manual. The system will confirm the registration
with a short sound signal and red light of LED indicator.
Saving changes:
To finish the recording of the engine compartment module, press VALET button once, the series
of red and green flashes of the status LED will confirm the saving, switch on the ignition to save the
settings and exit programming mode.
Level 11 – Programming and configuring ”Immobilizer PIN code”
To program the ”Immobilizer PIN code”, enter the programming mode and press VALET button 11
times. The level is divided into 3 sublevels (Sublevel 11.1 – Selecting buttons; sublevel 11.2 entering
PIN-code; sublevel 11.3 – confirmation of the PIN-code input).
To program the ”Immobilizer PIN code”, enter the programming mode and press VALET button 11
times. The level is divided into 3 sublevels (Sublevel 11.1 – Selecting buttons; sublevel 11.2 entering
PIN-code; sublevel 11.3 – confirmation of the PIN-code input).
It is necessary to configure an analog input (INP) as ‘Code immobilizer’ in the settings of the base
unit inputs when implementing the “Code immobilizer” via an analog input.
After selecting active buttons enter the sublevel 11.2 (Entering PIN-code) by pressing VALET button
once. Program PIN-code using selected buttons at this sublevel; press VALET button once and enter PIN-
code again. To confirm PIN-code re-entering and save all the settings press VALET button once again.
Sublevel 11.1 - Selecting buttons:
This sublevel is used to select active buttons via ‘Code Immobilizer’ analog input. To determine the
activity of the analog ”Code Immobilizer” input, apply potential to the corresponding input (INP) of the
base unit, LED indicator will be flashing orange.
To enter the next sublevel 11.2l press VALET button once.
Sublevel 11.2 - Entering PIN-code:
Program immobilizer deactivation PIN-code using selected button or buttons. Enter the first digit
by pressing the previously selected button (pauses between presses should not exceed 1 second). The
base unit will confirm entering with red flash of LED indicator. Enter the second (third, fourth) digit by
pressing the previously selected button. The base unit will confirm entering of each digit with red flash
of LED indicator.
Input the required number of digits (up to 4) and then press VALET button. The system will confirm
receiving of the secret validator code with long red flash of LED indicator and will wait for confirmation
of PIN-code.
Sublevel 11.3 - Confirmation of the PIN-code input:
Enter PIN-code again similarly to the procedure (level 11.2 – Entering PIN-code) and press VALET
button. The system will confirm correct PIN-code with red and green flashes of LED indicator and will
memorize PIN-code, and then the system will proceed to programming mode awaiting level input.
Incorrect confirmation is indicated with long red flash of LED indicator, after that the system will return
to programming mode.
Level 15 – Disabling/enabling immobilizer tag
To disabling/enabling of immobilizer tag, enter programming menu and press VALET button 15
times. LED indicator will light green (green light indicates enabled tag) and the system will wait for the
“Secret PIN-code” entering. Red light of LED indicates disabled immobilizer tag.
Disabling radio tag:
LED indicator will light green after entering the programming level. The system will wait for entering
the ‘Secret PIN-code’. Enter the ‘Secret PIN-code’ that is written on the owner’s plastic card. The system
will confirm disabling of the radio tag with two sound signals of the siren and a long red LED flash. After
that the system will return to the programming menu. If the PIN-code is not entered within 10 seconds
or the input is incorrect, a siren will sound one signal, LED will produce the series of red and green
flashes and the system will return to the programming menu.
Enabling radio tag:
LED indicator will light red after entering the programming level. The system will wait for action.
Press VALET button once to enable radio tag. The system will confirm enabling with one short sound
signal of a siren and a green LED light. After that the system will return to the programming menu.
Level 16 – Updating built-in Bluetooth modem firmware
Download the firmware from www.pandorainfo.com and install Pandora BT application on
your mobile device (Android version 4.4 or high or iOS version 9.3.5 and higher) with Bluetooth
4.0 Low Energy or higher support).
To update firmware of the built-in Bluetooth modem, enter programming mode and press VALET
button 16 times. Find your system in the mobile application, go to detected devices and select one
of the updating option: File manager (for Android only) or Internet and update Bluetooth modem
firmware. File manager allows to upload the firmware from the phone storage and Internet option
allows to upload Firmware from the server to the base unit.
Level 18 – Pairing and unpairing mobile device
The system supports only one mobile device. Pairing of a new mobile device (if the system has
previously paired device) is not allowed without unpairing procedure. When you overwrite the same
device in the system memory, you should delete the Bluetooth connection on your mobile device, delete
the mobile device from the system memory and then pair the mobile device in the system memory.
To pair a mobile device, enter the programming mode and press VALET button 18 times. LED
indicator will light green (green light indicates the system is ready to pair a mobile device) and the
system will enter the mobile device pairing mode. Red light of LED indicates the system has already had
registered mobile device, overwriting of mobile device can be done only after unpairing procedure.
Pairing mobile device:
LED indicator will light green after entering the level. Open ‘Pandora Online’ mobile application, go
to ‘Bluetooth Control’ –> ‘Not specified’ menu (‘Bluetooth device’ for iOS). This setting will be available
after adding the system in the account. The application will search for the system via Bluetooth
connection. Select the found system, the system and the mobile device will be automatically paired.
The system will confirm the pairing with a sound signal of a siren and red light of LED indicator.
Unpairing mobile device:
LED indicator will light red after entering the level. Press VALET button and hold it for more than 4
seconds, release the button. The system will confirm deleting with the series of sound signals of a siren
and the system will return to mobile device registration mode (LED indicator will light green).
Saving changes:
To finish the registration of a mobile device, VALET button should be pressed once, the series of
red and green flashes of the status LED indicator will confirm the saving, switch on the ignition to
automatically save the settings and exit the programming mode.