9
8
USER MANUAL
MOTORCYCLE SERVICE-SECURITY SYSTEM PANDORA DXL 1200L
EN
Remote and automatic engine start
The system allows for remote engine start using a remote engine start command from a phone,
Internet-service or mobile applications and automatic engine start using preconfigured automatic
engine start function. The remote start functions can be used to heat the engine, charge the vehicle
battery.
Remote and automatic start can only be used when the system is armed. When using the remote
and automatic engine start functions, make sure that the motorcycle is securely fixed on a parking
position While system is in the remote or automatic start mode, it keeps performing all security
functions of all of the guarded zones excluding shock sensor. To compensate, motion sensor sensitivity
and responsiveness will be increased. If any guarded zone is triggered, the engine will be immediately
stopped and alarm mode will be entered. Herewith all engine blocking functions will be activated.
Remote engine start control
If the system is prepared for remote start, use one of the method described below to execute it.
Phone
Call the system phone number. Wait it answer and enter the command code
.
If you send the command
, again during remote engine start, the engine operating time
will be increased by 10 minutes. This procedure can be performed many times.
Enter the command
to stop the engine..
Mobile application
Open the mobile application. When thy system is active, press and hold the button
START
ENGINE
on the
control panel until the scale is fully loaded. In a few seconds the engine will be started, it will be
confirmed with the spinning engine operation icon
. To remotely stop the engine while it performs
heating, press and hold the button
STOP
ENGINE
. In a few seconds the engine will be stopped, it will be confirmed
with the fading of engine operation icon
.
Internet service
Log in to the pandora-on.com. When thy system is active, press and hold the button
START
ENGINE
on the
control panel. In a few seconds the engine will be started, it will be confirmed with the spinning engine
operation icon
on the control panel. To remotely stop the engine while it performs heating, press
and hold the button
STOP
ENGINE
. In a few seconds the engine will be stopped, it will be confirmed with the
fading of engine operation icon
.
3 flashes
Engine is running
The system is armed
Engine stop
START
ENGINE
STOP
ENGINE
Automatic engine stop
by time or temperature
Prolong engine
operation for 10 minutes
Automatic engine start
The system allows setting up modes of the automatic engine start and stop using the Internet service, mobile
applications and phone. The automatic engine starts can be implemented according to the schedule, by
time period, by temperature, by voltage. Temperature and time conditions for stopping the engine control
the automatic and remote engine starts. If one of the stopping event occurs, the system will stop the engine
or will not allow starting it.
WARNING! ENGINE START VIA TEMPERATURE IS AVAILABLE ONLY IF TEMPERATURE
SENSOR IS CONNECTED. THE SENSOR AVAILABILITY DEPENDS ON THE SYSTEM SET.
Control over the system via a phone
WARNING! FOR THE CORRECT OPERATION OF THE GSM FUNCTIONS, THE OWNER
SHOULD MONITOR THE STATUS/BALANCE OF THE SIM CARD INSTALLED IN THE SYS-
TEM. IF THE SIM CARD IS BLOCKED OR DEFECTIVE, GSM FUNCTIONS OF THE SYSTEM
WILL BE UNAVAILABLE.
Call the system’s phone number. When it answers, enter command code.
WARNING! IF THE CALL IS NOT MADE FROM THE OWNER’S NUMBER, GUEST PIN-
CODE SHOULD BE ENTERED. FACTORY SET GUEST PIN CODE IS 1-2-3-4. AFTER
THESYSTEM IS INSTALLED, PLEASE CHANGE FACTORY SET PIN-CODE. 1-2-3-4.
DTMF – COMMANDS.
For example: To have simple access to engine start function, create a new contact in the contact
list of your phone, name it ‘Engine start’, for instance, and add the number in the following format:
+XXXXXXXXXXX,123*,297* where ‘+XXXXXXXXXXX’ – the system phone number, ‘,’ - pause is a feature
of the phone (can be displayed as the ‘P’, see the instructions of the phone), ‘123*’ - remote engine start
DTMF command, ‘297*’ - end call DTMF command.
#
#
9
9
*
*
*
*
9
9
0
0
*
*
1
1
0
0
0
0
*
*
1
1
2
2
3
3
*
*
Return to previous menu state
Repeat the last message
Silent arming
Help
0
0
0
0
*
*
0
0
1
1
*
*
Silent disarming
1
1
*
*
Arming
0
0
*
*
Disarming
Event history
5
5
1
1
*
*
Tow truck mode
Request GSM account balance
Start the engine/prolong heating
3
3
2
2
1
1
*
*
Stop the engine
3
3
3
3
3
3
*
*
This function is not used in DXL 1200L
5
5
0
0
0
0
*
*
4
4
5
5
6
6
*
*
6
6
5
5
4
4
*
*
6
6
6
6
6
6
*
*
9
9
9
9
9
9
*
*
2
2
5
5
8
8
*
*
System information
Request current coordinates
Switch on additional channel
Switch off additional channel
1
1
5
5
6
6
*
*
6
6
5
5
1
1
*
*
This function is not used in DXL 1200L
This function is not used in DXL 1200L
Enable engine blocking
Disable engine blocking
9
9
9
9
8
8
*
*
Disable immobilizer tag
8
8
8
8
8
8
*
*
Enable immobilizer tag
2
2
2
2
2
2
*
*
Disable Hands Free mode
2
2
2
2
3
3
*
*
Enable Hands Free arming
2
2
2
2
4
4
*
*
Enable Hands Free disarming
2
2
2
2
5
5
*
*
Enable HF disarming only with autom. start
7
7
8
8
9
9
*
*
Enable automatic engine start
9
9
8
8
7
7
*
*
Disable automatic engine start
2
2
9
9
7
7
*
*
Call ended
5
5
5
5
1
1
*
*
Enable maintenance mode (see description below)
5
5
5
5
2
2
*
*
Disable maintenance mode
