background image

7

6

USER MANUAL

 

MOTORCYCLE SERVICE-SECURITY SYSTEM PANDORA DXL 1200L

EN

”Slave” mode

This mode is disabled by default. Additional connections and settings are required to enable this mode. 

This mode allows arming and disarming using special analog inputs of the system connected to the 

vehicle buttons, levers or pedals. To arm the system, press the button/lever or pedal when the ignition 

is switched off. The system will be automatically armed. To disarm the system press the button/lever/

pedal (if  ”Disable disarming when the tag is not present” setting is enabled, disarming procedure will 

be performed only if there is a tag in the radio zone).

Backup battery

A built-in battery can prolong system operation in the armed 

mode. It allows system to send a notification to the owner in 

case of an unauthorized power disconnection. Emergency 

power supply can be also activated at a short-time voltage 

drop at the moment of starting the engine.

If the built-in battery is discharged, the system will 

automatically start charging it when the ignition is switched 

on and the voltage is more than 13V.

Replacing immobilizer tag battery 

Carefully open the cover of the tag’s battery compartment. Extract discharged battery and insert a new 

one keeping in mind the correct polarity. Replacing a battery will not cause a loss of tag code information, 

as authorization data is stored in the non-volatile memory of the MCU.

Carefully close the cover of the tag’s battery compartment. All elements of construction should be 

rigidly locked in places. If it is so, the tag can be operated as usually.

CONTROL OVER THE SYSTEM
Arming

To arm the system when the ignition is switched off, use one of the methods described below. The 

system will confirm the command receiving with 1 short sound signal and 1 flash of turn indicators.

Button on the radio tag

The radio tag should be in the Bluetooth coverage area. Shortly press the tag button 

.

”Hands Free”

Move with the remote tag away   from the vehicle at a distance greater than the regular radio 

coverage.

”Clutch lever”

Press the clutch lever when a radio tag is in the coverage zone  

”SlAVE”

Press the button/lever/pedal.

Open here

1 Flash

1 Flash

1x

CALL
SLAVE

HANDS FREE
MOBILE APP
PANDORA-ON

.COM

Phone

Call the system phone number. Wait it answer and enter the command code  

To arm the system without a siren sound, enter the command code  

.

Mobile application

Open the mobile application. When thy system is active, press and hold the button    on the 

control panel until the scale is fully loaded.

Internet service

Log in to the PANDORA-ON.COM. When thy system is active, press and hold the button    on the 

control panel.

”VALET” button

Press and hold the VALET button for 3 seconds. The system will be armed in 30 seconds. The LED 

indicator is lighting red during the countdown. 

Disarming

To disarm the system, use one of the methods described below. The system will confirm the 

command receiving with 2 short sound signal and 2 flash of turn indicators.

WARNING! IF “DISABLE DISARMING WHEN THE TAG IS NOT PRESENT” SETTING IS 

ENABLED, DISARMING PROCEDURE WILL BE PERFORMED ONLY IF THERE IS A TAG IN 

THE RADIO ZONE (IT DOESN’T APPLY TO DISARMING VIA A PHONE, INTERNET SER-

VICE AND MOBILE APPLICATIONS)

Button on the radio tag

The radio tag should be in the Bluetooth coverage area. Shortly press the tag button  

.

”HANDS FREE” 

Move toward the vehicle with remote tag    - enter the coverage area of the radio channel of the 

system.

”Clutch lever”

Press the clutch lever when a radio tag is in the coverage zone  

.

”SLAVE”

Press the button/lever/pedal.

Phone

Call the system phone number. Wait it answer and enter the command code 

.

To disarm the system without a siren sound, enter the command code  

.

Mobile application

Open the mobile application. When thy system is active, press and hold the button     on the 

control panel until the scale is fully loaded.

 Internet service

Log in to the pandora-on.com. When thy system is active, press and hold the button    on the 

control panel.

”VALET” button

Enter the ”Secret PIN-code” (see ”Emergency disarming using the VALET button” section).

2 Flashes

2 Flashes

2x

CALL
SLAVE

HANDS FREE
MOBILE APP
PANDORA-ON

.COM

Summary of Contents for DXL 1200L




































Reviews: