19
18
USER MANUAL
MOTORCYCLE SERVICE-SECURITY SYSTEM PANDORA DXL 1200L
EN
In preparation to the programming these stages should be followed:
• connect the system and PC via USB cable;
• start Pandora Alarm Studio;
• enter the programming settings mode by entering the service PIN-code.
Pandora Alarm Studio will automatically connect to the system and open access to the settings and
firmware updates.
Updating firmware:
It is recommended to update firmware of the base unit before installing and programming the
system (actual version of the firmware you can download from pandorainfo.com). You can update
firmware using Alarm Studio application after entering programming mode or using quick boot
algorithm (PIN-code is not required).
Quick boot mode: open Alarm Studio; de-energize and disconnect the system; press and hold
VALET button located on the base unit; release the button immediately after connecting the system
and a computer via USB cable; the system will enter boot mode.
If the boot mode has been interrupted for some reason and the status indicator lights red, you need
to load firmware using quick boot mode (without entering PIN-code).
Programming using the VALET button
The system allows programming some settings using VALET button. To configure all settings use a
computer to program the system.
Programming levels table
Level 1
Recording radio tags into the system’s memory (BT760)
Level 2
Changing the factory preset of the service PIN-code
Level 3
Recording the idle speed to the system memory
Level 4
Resetting to factory settings
Level 5
Recording Bluetooth module (RHM-03 BT)
Levels 6, 7
Recording Bluetooth radio relays №1, №2 (BTR-101)
Level 8
Recording external Bluetooth GPS/GLONASS receiver (NAV-035 BT)
Level 11
Programming and configuring ‘Immobilizer PIN code’
Level 15
Emergency disabling of immobilizer radio tag
Level 16
Updating Bluetooth modem firmware
Level 18
Pairing and unpairing mobile device
Levels 19, 20
Updating radio relays №1, №2 firmware (BTR-101)
Level 21
Updating Bluetooth module firmware (RHM-03 BT)
Level 22
Updating Bluetooth GPS/GLONASS receiver firmware (NAV-035 BT)
Levels 23, 24
Recording door sensors №1, №2 (DMS-100 BT)
Levels 25, 26
Updating door sensors №1, №2 firmware (DMS-100 BT)
Enter programming mode by entering the ‘Service PIN-code’, Use VALET button to enter the desired
level number (press the button a number of times, equal to level number; pauses between presses
should not exceed 1 second). The system will confirm correct input with red LED flashes and short
sound signals of a siren and proceed to the desired level. If the input was incorrect, the system will not
confirm input and will await a new level input after a series of green and red flashes.
Level 1 – Recording radio tags into the system’s memory
Prepare to record all radio tags (you can record up to 3 tags), install batteries in the radio tags.
Enter programming menu and then press VALET button once. LED indicator will light green and
the system will enter the tag recording mode. Tags are recorded (paired) one by one, in any order and
without time limit. All previously registered radio tags will be removed when you overwrite new tags
or overwrite old tags.
Recording radio tags:
Press control button on a tag and hold it for 6 seconds (6 flashes of tag status indicator), release the
button after the sixth flash. If the recording was successful, a siren will emit 1 beep, after that you can
move to recording the next tag
Saving changes:
To finish the recording of radio tags into the system, VALET button should be pressed once again,
the series of red and green flashes of status LED indicator will confirm the saving.
Level 2 – Changing the factory preset of the service PIN-code
Prepare a new value of the ‘Service PIN-code’, it should consist of 4 digits (from 1 to 9). Write down
or remember the new PIN-code.
Enter programming menu and then press VALET button twice. The system will enter ‘Changing
Service PIN-code’ mode and the status LED indicator will turn off.
Changing the ‘Service PIN-code’:
• Enter the first digit of the code using VALET button. Press the button a number of times, equals
to the first digit. Pauses between presses should not exceed 1 second, every pressing will confirm with
orange LED indicator flash. Pause for more than 1 second and red LED indicator confirms the input of
the first digit. Then you can enter the next digit.
• Enter the other numbers in the same manner. The input of the fourth number will be confirmed
by series of red and green LED indicator flashes. The system will wait for PIN-code re-entering.
• Enter all four digits again;
• If you were able to correctly enter the ‘Service PIN-code’ twice, the indicator will produce the series
of red and green flashes, new PIN-code will be recorded, the system will return to programming mode.
In case of the incorrect code input the indicator will be lit red, the system will return to programming
mode.
Level 3 – Recording the idle speed to the system memory
To timely turn off the starter during automatic or remote engine start via analog tachometer input,
it is necessary to record the engine idle speed. To record idle speed to the non-volatile system memory,
enter the programming menu. Press VALET button three times. Switch on the ignition and start the
engine after entering this level of programming (the engine should be warmed-up, idle speed should
match the stable idle speed of the warmed-up engine). The system will confirm the presence of the idle
speed status with green flashes of LED indicator. Wait until the stable idle speed will be reached and
save the changes.
Saving changes:
Press VALET button once to save idle speed. Successful recording of the idle speed will be confirmed
with the series of red and green flashes of LED indicator. The system will exit programming menu and
reboot after saving the idle speed.
Level 4 – Resetting to factory settings.
The procedure recovers the factory settings of the system without deleting previously registered
devices (tags, mobile device, relays, etc.) that is stored in the non-volatile memory.
To reset the settings enter the programming mode and press VALET button four times. Press and
hold VALET button for more than 4 seconds until siren sound, then release the button. The system will
confirm the resetting to the factory settings with a long red flash of LED indicator. After that the system
will return to a programming mode
Level 5 – Recording Bluetooth module
To record a Bluetooth module, enter programming mode and press VALET button 5 times. The LED
indicator will light green and the system will enter the recording of an engine compartment module
