Panasonic WJ-HD616G Installation Manual Download

Page: 135 / 156

135

Add a hard disk drive

When adding an HDD unit, proceed as follows.
It is possible to add an HDD unit without stopping operation.
Hard disk drives will be locally procured.

Install an HDD unit in the recorder

(

☞

Page 52)

Hard disk drive auto recognition

(

☞

Page 136)

➜

The hard disk drive is installed as a record-

able disk.

Add a hard disk drive to the system.

(Link process)

(

☞

Page 137)

The hard disk drive is installed as a playback-

only disk.

The hard disk drive is installed as a recordable

disk.

The hard disk drives can be installed/removed from the HDD slots covered by the front panel (operating section).
Contact your dealer for purchasing the hard disk drives.

Important:

• Hard disk drives are precise devices. Handle with care while keeping the following in mind.

• Do not subject the hard disk drive to any vibration or impact.

• Before touching the hard disk drive, eliminate static electricity by touching a steel locker, etc. When holding the hard disk

drive, hold the both sides of the hard disk drive.

• Do not touch the circuit board or the connectors to prevent the hard disk drive from damaging by static electricity.

• Contact your dealer for hard disk drives that works on the recorder. Please be forewarned that operation with any hard disk

drive other than the specified models is not guaranteed under any circumstances.

• When using multiple hard disk drives, use the same model.

If different models are used together, even when the capacities of them are the same, the available capacity may be a few

percent smaller.

• Install the hard disk drives one by one in order starting from HDD1.

(The leftmost slot of the HDD slots is HDD1 and the rightmost one is HDD4.)

• Once the operation has started in the RAID 5 or RAID 6 mode, do not change the positions of the HDD units. If they are

changed, it may become impossible to read recorded data.

When a hard disk drive is
not formatted

Start auto format

➜

When a hard disk drive is
formatted

➜

When recording on the newly
installed hard disk drive

➜

Summary of Contents for WJ-HD616G





























































































































































Search results

Summary of Contents for WJ-HD616G

Reviews:

Related manuals for WJ-HD616G

Brands by name

Popular brands

Panasonic WJ-HD616G, Installation Manual

Search results

Summary of Contents for WJ-HD616G

Reviews:

Related manuals for WJ-HD616G

Brands by name

Popular brands