Panasonic Varicam 35, Operating Manual

Page: 136 / 174

– 136 –
Chapter 11 Network Connection — Network settings
Network settings
Configuration of various settings are required to use the wireless LAN or the wired LAN. Configure the settings according to the function to use.
Wireless LAN settings
The setting to connect to computers using the wireless LAN.
1
Set each item in [MENU]
→
[PERIPHERAL]
→
[WIRELESS PROPERTY] as necessary.
[MAC ADDRESS]:
MAC address of wireless LAN (cannot be changed)
[SSID]:
Network name of the camera (SSID) ([AU-VREC1])
[BAND]:
Setting for switching between two transmission methods (2.4 GHz or 5 GHz) (Factory setting: [2.4GHz]) (for AJ-WM30: [2.4GHz], for
AJ-WM50: [2.4GHz] or [5GHz])
[CHANNEL(2.4GHz)]:
Channel used when set to 2.4 GHz (Factory setting: [AUTO])
[CHANNEL(5GHz)]:
Channel used when set to 5 GHz (Factory setting: [AUTO])
[ENCRYPT KEY]:
WPA2 encryption key (Factory setting: [01234567890123456789abcdef])
[IP ADDRESS]:
IP address of the camera (Factory setting: [192.168.0.1]).
[SUBNET MASK]:
Subnet mask (Factory setting: [255.255.255.0])
[DHCP SERVER]:
Setting whether to use DHCP SERVER function (
[ENABLE]:
Use DHCP SERVER function/
[DISABLE]:
Does not use DHCP
SERVER function) (Factory setting: [ENABLE])
2
From [MENU]
→
[PERIPHERAL]
→
[NETWORK SEL], select [WLAN].
The changed setting will be valid after rebooting the camera.
3
Select SSID from the list of the access points for mobile devices or computers and enter the password (encryption key).
Display the access point list screen in wireless setting and select [SSID] of the camera.
f
Factory setting: [AU-VREC1]
When the password confirmation screen appears, enter the password (encryption key).
f
Factory setting: [01234567890123456789abcdef]
4
Check the network connection.
Once the setting is completed, check that the network connection can be established from a computer.
@ @
NOTE
t
[IP ADDRESS] cannot be set between [192.168.155.1] and [192.168.155.255].
t
AJ-WM30 can only operate when the communication method is 2.4 GHz. It will operate after automatically setting to CH1 of 2.4 GHz when [BAND] is
set to [5GHz].
t
The startup time after turning on the power may be longer due to starting of the network.
t
When you change the settings of [NETWORK SEL], the changes will not be reflected until the camera is restarted. After the settings have been
changed, the setting screen termination may take time due to the restart of the network service.
t
All of the IP address, subnet mask, and default gateway must be correctly set.
Contact the network administrator if the [CANNOT ACCESS GATEWAY!] warning is displayed when closing the setting screen.
t
If you do not use default gateway and DNS, set them to [0.0.0.0].
DHCP and DNS may not function properly depending on the network environment.
Wired LAN settings
The settings to connect to computers using the wired LAN are as follows.
1
Set each item in [MENU]
→
[PERIPHERAL]
→
[LAN PROPERTY] as necessary.
[DHCP] and [DHCP SERVER] are mutually exclusive.
[MAC ADDRESS]:
MAC address of wired LAN (cannot be changed)
[DHCP]:
Setting whether to use automatic acquisition via DHCP (
[ENABLE]:
Use automatic acquisition/
[DISABLE]:
Does not use automatic
acquisition (Factory setting: [ENABLE])
[IP ADDRESS]:
IP address (Factory setting: [192.168.0.1]) (cannot be set when [DHCP] is set to [ENABLE])
[SUBNET MASK]:
Subnet mask (Factory setting: [255.255.255.0]) (cannot be set when [DHCP] is set to [ENABLE])
[DEFAULT GATEWAY]:
Default gateway (Factory setting: [192.168.0.254]) (cannot be set when [DHCP] is set to [ENABLE])
[PRIMARY DNS]:
Primary DNS server setting (Factory setting: [0.0.0.0])
[SECONDARY DNS]:
Secondary DNS server setting (Factory setting: [0.0.0.0])
[DHCP SERVER]:
DHCP SERVERSetting whether to use the function (
[ENABLE]:
Use the DHCP SERVER function/
[DISABLE]:
Do not use the
DHCP SERVER function) (Factory setting: [DISABLE]) (cannot set when [DHCP] is set to [ENABLE])
2
Select [LAN] in [MENU]
→
[PERIPHERAL]
→
[NETWORK SEL].
3
Configure the settings of wired LAN of your computer.
(For Windows)
Display [Properties] in [Internet Protocol Version 4 (TCP/IPv4)] and configure the settings. For details on how to display the screen, refer to [Start]
→
[Help and Support].
f
When [DHCP SERVER] is set to [ENABLE] on the camera
Select [Obtain an IP address automatically] and [Obtain DNS server address automatically] in the [General] tab. Select [Automatic private IP
address] in the [Alternate Configuration] tab.
f
When [DHCP SERVER] is set to [DISABLE] on the camera
Select [Use the following IP address] in the [General] tab.
-
[IP address]: Enter the same address as that of the camera.
-
[Subnet mask]: Enter the same value as that of the camera.