Panasonic S-160PE1R5A, Technical Data And Service Manual

Page: 212 / 218

8 8
C ont r ol of 2 W A Y SYSTEM
8 -15 . CZ-RWSC3
2. Wireless Remote Controller
OPERATION
TIM ER
STANDBY
FILTER
Installation Instructions
Wireless Receiver for ALL
(1) Light receiving section
Receives signals.
(2) Emergency operation button
Starts/Stops emergency operation.
(3) Indication lamp
Indicates operation status.
Supplied accessories
Wood screw
M 4 × 15.5
(2)
Clamper
(1)
Part Names
Saf ety Precautions
Read bef ore installation

Read the Installation Instructions carefully to install the
unit correctly and safely.
Be sure to read the Safety Precautions in particular
before installation.

After the installation is complete, perform test operation
to confirm that no abnormality is present.

We assume no responsibility for accidents or damages resulting
from methods other than those described in the installation
instructons or methods without using specified parts.
M alfunctions that occurred due to the unauthorised installation
methods are not covered by the product warranty.

Read the installation instructions supplied with indoor units as well.
WA RNI NG
This symbol refers to a haza rd or
unsafe practice which can result in
severe personal inj ury or death.
CA U TI ON
This symbol refers to a haza rd or unsafe
practice which can result in personal inj ury
or product or property damage.
WA RNI NG
Turn off the circuit breaker of
the units before installation.
Ask your dealer or
professionals for installation
and electric work.
This receiver shall be installed
in accordance with National
Wiring Regulations.
Securely connect and fix the
Do not allow the connection
to be exposed to the external
that sufficiently supports the
specified cables for wiring.
force of the cables.
Choose an installation location
weight of the receiver.
1. A ccessories
CA U TI ON

Do not use at the following locations.
Location where condensation occurs
Location where corrosive gases, etc. may leak
Location where voltage fluctuation frequently
Location where flammable gases, etc. may leak
Location with lots of water or oil droplets
(including machine oil)
occurs
Location where there is a machine producing
electromagnetic radiation
Location where droplets of organic solvents
spread
Location where acidic or alkaline solutions or
special sprays are frequently used

Do not operate with wet hands.

D o not wash with water.
Dimensions
70
4.4
4.4
2.
8
1
3.
8
1
83.5
20
120
34.4
8
5.4
Unit: mm
14
9 .4
12
C ont r ol of 2 W A Y SYSTEM
2. Wireless Remote Controller
2. I nstalling the Receiv er
1
Remov e the bottom case.
A ttention
M ounting the bottom case

Tighten the screws securely until the screw
heads touch the bottom case.
(Otherwise, loose screw heads may hit the
PCB and cause malfunction when mounting
the top case.)

Do not over-tighten the screws.
(The bottom case may be deformed, resulting
in fall of the unit.)
Connecting the remote controller wiring

Arrange the wires as shown in the illustration for (2) in step 2,
avoiding unnecessary wires being stored in the case. (Caught
wires may destroy the PCB.)

Avoid wires touching parts on the PCB.
(Caught wires may destroy the PCB.)
Flat-blade
screwdriver
Bottom
case
Insert the driver
and slightly turn.
2
M ount to the wall.
e p y t d e d d e b m E e p y t d e s o p x E
Preparation: M ak e 2 holes f or screws using a driv er. Preparation: M ak e 2 holes f or screws using a driv er.
(1) (3)
(2)
Cut here with a
nipper and remove
the burr with
. e l i f a
M ount the top case.

A lign the claws of
the top case and
then align the claws
of the bottom case.
M ount the bottom case
to the wall.
Connect the remote controller wiring.

Arrange the wires along the groove of the case.
Wood screw (supplied)
Claw
H ole for screw
e h t x i f o t ll a W
receiver
Claw (2 places)
Top case
(Back side)
Remove the coating. Approx. 6 mm
Remove the sheath. Approx. 150 mm
M ake sure the wiring connection
is in the correct direction.
Clamper
(supplied)
Pass through
the hole.
Bottom case (Back side)
(1) (3)
Avoid the wire
being caught.
M ount the top case.

A lign the claws of
the top case and
then align the claws
of the bottom case.
M ount the bottom case to
the wall.

Pass the wire through the hole
in the centre of the bottom case.
Connect the remote controller wiring.
Wood screw (supplied)
Claw (2 places)
Claw
H ole for screw
Terminal board
Bottom case (Back side)
Remov e the coating.
A pprox. 6 mm
M ake sure the wiring connection
is in the correct direction.
Top case
(Back side)
(2)
8-16
SM830262-00_大洋州向け シングル天埋_TD&SM.indb 16 17/12/27 14:24:2