Panasonic PT-RQ32KU, Operating Instructions Manual

Page: 173 / 285

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 173
[SYSTEM SELECTOR]
Switches the [SYSTEM SELECTOR] setting according to the input signal of the image being
projected.
f
When the input is SDI1 to SDI4 equipped on this projector as the standard projector.
g
The [DISPLAY OPTION] menu
→
[SDI IN]
→
[SINGLE LINK SETTING]
→
[SDI1]/[SDI2]/[SDI3]/
[SDI4]
→
[SYSTEM SELECTOR]
g
The [DISPLAY OPTION] menu
→
[SDI IN]
→
[DUAL LINK SETTING]
→
[SDI1-2]/[SDI3-4]
→
[SYSTEM SELECTOR]
g
The [DISPLAY OPTION] menu
→
[SDI IN]
→
[QUAD LINK SETTING]
→
[SYSTEM SELECTOR]
f
When the input is SDI1 to SDI4 on the Interface Board
g
The [DISPLAY OPTION] menu → [SLOT IN] → [SINGLE LINK SETTING] → [SDI1 [SLOT1]]/
[SDI2 [SLOT1]]/[SDI3 [SLOT2]]/[SDI4 [SLOT2]] → [SYSTEM SELECTOR]
g
The [DISPLAY OPTION] menu → [SLOT IN] → [DUAL LINK SETTING] → [SYSTEM
SELECTOR]
g
The [DISPLAY OPTION] menu → [SLOT IN] → [QUAD LINK SETTING] → [SYSTEM
SELECTOR]
f
When the input is anything other than SDI
The [PICTURE] menu
→
[SYSTEM SELECTOR]
[SYSTEM DAYLIGHT VIEW]
Switches the [SYSTEM DAYLIGHT VIEW] setting. (
x
page 96)
[FREEZE]
Temporarily pauses the image. (
x
page 141)
[WAVEFORM MONITOR] Displays the waveform of the input signal. (
x
page 141)
[LENS MEMORY LOAD]
Loads the registered lens memory. (
x
page 147)
[PROJECTION METHOD]
Switches the [PROJECTION METHOD] setting. (
x
page 144)
4) Press the <ENTER> button.
[STATUS]
Display the status of the projector.
1) Press
as
to select [STATUS].
2) Press the <ENTER> button.
f
The [STATUS] screen is displayed.
3) Press
qw
to switch the pages.
f
The page will change each time you press the button.
[PROJECTOR TYPE] Displays the projector type and serial number of the projector.
[PROJECTOR RUNTIME] Displays the runtime of the projector.
[LIGHT RUNTIME] Displays the runtime of the light source 1 and the light source 2.
[MAIN/SUB VERSION] Displays the main and sub versions of the firmware of the projector.
[INTAKE AIR TEMP.]
*1
Displays the status of the intake air temperature of the projector.
[OPTICS MODULE TEMP.]
*1
Displays the status of the internal temperature of the projector.
[EXHAUST AIR TEMP.]
*1
Displays the status of the exhaust air temperature of the projector.
[LIGHT1-B TEMP.]
*1
Displays the light source 1 temperature status of the projector.
[LIGHT1-S TEMP.]
*1
[LIGHT2-B TEMP.]
*1
Displays the light source 2 temperature status of the projector.
[LIGHT2-S TEMP.]
*1
[SELF TEST] Displays the status of the projector.
[INPUT]
Displays the input terminal currently selected.
Displays the representative input terminal when one image is displayed with multiple input signals.
[SIGNAL NAME] Displays the input signal name.
[MEMORY NO.] Displays the memory number of the input signal.
[BACKUP INPUT STATUS]
Displays whether switching to the backup input signal is possible or not when [BACKUP INPUT
MODE] is set to [OFF]. (
x
page 115)
[NUMBER OF REGISTERED
SIGNAL]
Displays the number of registered signals.
[COOLING CONDITION] Displays the set cooling conditions.
[ATMOSPHERIC PRESSURE] Displays the atmospheric pressure.
[REMOTE2 STATUS] Displays the control status of the REMOTE2.
[AC VOLTAGE] Displays the input supply voltage.
[LENS TYPE]
*2
Displays the type name (type of the projection lens) set to the projection lens.
[LENS ID]
*2
Displays the ID set to the projection lens.