Panasonic MADHT1105 Operating Instructions Manual Download Page 181

Page: 181 / 394

4-13

Note

Related page

• For parameters which No. have a suffix of “

”

, changed contents will be validated when

you turn on the control power.

• P.3-30... “Inputs and outputs on connector X4”

Before

Using

the

Products

Preparation

Connection

Setup

Adjustment

When

Trouble

Supplement

Pr1.05

Title

2nd gain of position loop

control mode

S T

Range

0 to 30000

Unit

0.1/s

Default

A,B,C-frame

570

D,E,F-frame

380

Pr1.06

Title

2nd gain of velocity loop

control mode

P S T F

Range

1 to 32767

Unit

0.1Hz

Default

A,B,C-frame

270

D,E,F-frame

180

Pr1.07

Title

2nd time constant of velocity loop integration

control mode

P S T F

Range

1 to 10000

Unit

0.1ms

Default

10000

Pr1.08

Title

2nd filter of speed detection

control mode

P S T F

Range

0 to 5

Unit

—

Default

Pr1.09

Title

2nd time constant of torque filter

control mode

P S T F

Range

0 to 2500

Unit

0.01ms

Default

A,B,C-frame

D,E,F-frame

126

Related page

Position loop, velocity loop, speed detection filter and torque command filter have their 2

pairs of gain or time constant (1st and 2nd).

For details of switching the 1st and the 2nd gain or the time constant, refer to P.5-17 "Gain

Switching Function" of Adjustment.

The function and the content of each parameter is as same as that of the 1st gain and time

constant.

Pr1.10

Title

Velocity feed forward gain

control mode

S T

Range

0 to 1000

Unit

0.10%

Default

300

Multiply the velocity control command calculated according to the internal positional

command by the ratio of this parameter and add the result to the speed command resulting

from the positional control process.

Pr1.11

Title

Velocity feed forward filter

control mode

S T

Range

0 to 6400

Unit

0.01ms

Default

Set the time constant of 1st delay filter which affects the input of velocity feed forward.

<Usage example of velocity feed forward>

The velocity feed forward will become effective as the velocity feed forward gain is gradually

increased with the velocity feed forward filter set at approx. 50 (0.5 ms). The positional

deviation during operation at a constant velocity is reduced as shown in the equation below

in proportion to the value of velocity feed forward gain.

Positional deviation [unit of command] = command speed [unit of command/s] /

positional loop gain [1/s] × (100 - velocity feed forward gain [%]) / 100

1. Details of parameter

[Class 1] Gain adjustment

Summary of Contents for MADHT1105











































































































































































































































































































































































































Search results

Summary of Contents for MADHT1105

Reviews:

Related manuals for MADHT1105

Brands by name

Popular brands

Panasonic MADHT1105, Operating Instructions Manual

Search results

Summary of Contents for MADHT1105

Reviews:

Related manuals for MADHT1105

Brands by name

Popular brands