Panasonic KX-TG2357 Operating Instructions Manual Download Page 61

Page: 61 / 92

Ans

ering System

For assistance, please call: 1-800-211-PANA(7262)

Recording a Memo Message

You can record a voice memo message of up to 3 minutes in memory.

• If you record for over 3 minutes in step 2, the unit will stop recording.
• If “ ” is displayed, 6 beeps sound and “

Your message was not recorded. Record your

message again.

” is announced, start again from step 1.

Press

[MEMO]

After the long beep, talk clearly 20 cm
(8 inches) away from the

MIC

• The base unit display shows the elapsed

recording time.

• If the elapsed recording time exceeds 99

seconds, the counter continues from 00 to
indicate 100 seconds.

When finished, press

[MEMO]

[STOP]

• The NEW MESSAGE indicator flashes.

Base Unit

[STOP]

MIC

[MEMO]

NEW MESSAGE Indicator

PQQX13991YA.book 61 ページ２００４年２月２５日　水曜日　午前１１時１２分

Summary of Contents for KX-TG2357





























































































Search results

Summary of Contents for KX-TG2357

Reviews:

Related manuals for KX-TG2357

Brands by name

Popular brands

Panasonic KX-TG2357, Operating Instructions Manual

Search results

Summary of Contents for KX-TG2357

Reviews:

Related manuals for KX-TG2357

Brands by name

Popular brands