Panasonic KX-TG2357 Operating Instructions Manual Download Page 62

Page: 62 / 92

Remote Operation from a Touch Tone Phone

While outside, you can operate the Answering System from any touch tone phone.
A synthesized voice menu will guide you through the Answering System (p. 64).
• To skip the voice menu and operate the unit directly, see page 65.

Summary of remote operation

• The unit will announce the remaining recording time after playback if it is less than

3 minutes.

• The messages are saved.
* If “

No new messages

” is announced, the unit has only old messages.

If “

No messages

” is announced, the unit has no messages.

Call your unit from a touch tone phone.

Enter your remote code (p. 63) during or after the

greeting message.

• The number of new messages is heard, and the

new messages will be played.*

After 3 seconds, the voice menu will start (p. 64).

Follow the menu or enter direct commands (p. 65).

To end remote operation, hang up.

PQQX13991YA.book 62 ページ２００４年２月２５日　水曜日　午前１１時１２分

Summary of Contents for KX-TG2357





























































































Search results

Summary of Contents for KX-TG2357

Reviews:

Related manuals for KX-TG2357

Brands by name

Popular brands

Panasonic KX-TG2357, Operating Instructions Manual

Search results

Summary of Contents for KX-TG2357

Reviews:

Related manuals for KX-TG2357

Brands by name

Popular brands