Panasonic KX-TG2357 Operating Instructions Manual Download Page 57

Page: 57 / 92

Ans

ering System

For assistance, please call: 1-800-211-PANA(7262)

Listening to Messages

Using the Base Unit

You can see the total number of recorded messages on the base unit display. If the
NEW MESSAGE indicator flashes on the base unit, new messages have been
recorded.

To play back messages

Press

[MESSAGE]

• The unit announces the number of new

messages and only new messages are played
back.

• When you have no new messages, the unit

announces “

No new messages. All message

playback

” and plays back all messages.

• When you have no messages, the unit

announces “

No messages

”.

• During playback, the display shows the message number.
• At the end of the last message, “

End of final message

” is heard. The unit will

announce the remaining recording time if it is less than 3 minutes.

• If a call is received during playback, the unit rings and playback stops. To answer

the call, press

[SP-PHONE]

. For playback, start again from the beginning after

hanging up.

Voice Day/Time Stamp:

During playback, the unit will announce the day and

time when each message was recorded (p. 14).

Base Unit

[MESSAGE]

NEW MESSAGE Indicator

PQQX13991YA.book 57 ページ２００４年２月２５日　水曜日　午前１１時１２分

Summary of Contents for KX-TG2357





























































































Search results

Summary of Contents for KX-TG2357

Reviews:

Related manuals for KX-TG2357

Brands by name

Popular brands

Panasonic KX-TG2357, Operating Instructions Manual

Search results

Summary of Contents for KX-TG2357

Reviews:

Related manuals for KX-TG2357

Brands by name

Popular brands