Panasonic KX-TCD961EB Operating Instructions Manual Download | Manualshive

Page: 67 / 68

background image

67

Chapter 6

Useful Information

GUARANTEE

CONDITIONS OF GUARANTEE

This guarantee is in addition to and does not in any way affect any statutory or other
rights of consumer purchasers. If within the applicable guarantee period, the appliance
proves to be defective by reason of faulty design, workmanship or materials, we
undertake subject to the following conditions to have the defective appliance (or any part
or parts there of) repaired or replaced free of charge.
1. The appliance shall have been purchased and used solely within the UK and in

accordance with standard operating instructions and the technical and/or Safety
Standards required in the UK.

2. The appliance should be returned together with this guarantee and proof of date of

purchase promptly on being found defective at the purchaser’s risk and expense to
the authorised dealer from whom the appliance was purchased or to the nearest
authorised dealer. All enquires must be through such dealers.

3. This guarantee shall not apply to damage caused through fire, accident, lightning,

misuse, wear and tear, neglect, incorrect adjustment or repair, to damage caused
through installation, adaption, modification or use in an improper manner or
inconsistent with the technical and/or safety standards required in the country where
this appliance is used, or to damage occurred during transit to or from the purchaser.

4. If at any time during the guarantee period any part or parts of the appliance are

replaced with a part or parts not supplied or approved by us or of an objective quality
safe and suitable for the appliance, or the appliance has been dismantled or repaired
by any person not authorised by us, we shall have the right to terminate this
guarantee in whole or in part immediately without further notice.

5. The purchaser’s sole and exclusive remedy under this guarantee against us is for the

repair or replacement of the appliance or any defective part or parts and no other
remedy, including, but not limited to, incidental or consequential damage or loss of
whatsoever nature shall be available to the purchaser.

6. This guarantee shall not apply to cassette tapes, batteries and any other items of

limited natural life.

7. Our decision on all matters relating to complaints shall be final. Any appliance or

defective part which has been replaced shall become our property.

8. The guarantee period applicable to this product shall be 12 months.

Please keep these Operating Instructions with your receipt.

Panasonic Business Systems U.K.

Receipt No.

Date of Purchase

Model No. KX-TCD961EB

Serial No.

KX-TCD961EB.6(57~68) 99.9.27 7:30 PM Page 67

«
...
65
66
67
68
»

Summary of Contents for KX-TCD961EB





































































Reviews:

No comments

Related manuals for KX-TCD961EB

Brand: Panasonic Pages: 66

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Paradyne Pages: 17

Brand: Unify Pages: 144

Brand: UniData Communication Systems Pages: 60

Brand: Guardian Telecom Pages: 16

Brand: Scitec Pages: 1

Brand: Radio Shack Pages: 16

Brand: Channel Plus Pages: 2

Brand: Mitel Pages: 24

DS3111-2 - DECT 6.0 Cordless Phone

Brand: VTech Pages: 1

Brand: Daewoo International Pages: 26

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands