Panasonic KX-TCD961EB Operating Instructions Manual Download

Page: 60 / 68

Before Requesting Help

Problem

“ ” flashes and an alarm tone sounds
when you press

A busy tone sounds when you
press

“

” flashes during a conversation and

the call is disconnected.

Static, sound cuts in/out, fades.
Interference from other electrical units.

The handset does not ring.

The base unit does not ring.

You cannot dial.

You cannot redial.

Remedy

•

You are too far from the base unit. Move closer and
try again.

•

Plug in the AC adaptor.

•

Another handset is in use.

•

The handset is out of range. Move closer to the base
unit and make the call again.

•

Plug in the AC adaptor.

•

Locate the handset and base unit away from other
electrical appliances (p. 5).

•

Move closer to the base unit.

•

Turn the power ON (p. 14).

•

The ringer is set to OFF. Select the desired volume
level (p. 16).

•

The ringer is set to OFF. Set to HIGH, MEDIUM or
LOW (p. 17).

•

Check that the dialling mode selection is correct
(p. 15).

•

The unit is in call prohibition mode. Cancel the mode
(p. 33).

•

The dialled number is restricted. Cancel the number
(p. 34).

•

Key lock mode is set. Cancel the mode (p. 28).

•

Access numbers entered after pressing

will not

be included when redialling.

•

If the last number dialled was more than 24 digits
long, the number will not be redialled.

Cordless Telephone

KX-TCD961EB.6(57~68) 99.9.27 7:30 PM Page 60

Summary of Contents for KX-TCD961EB





































































Search results

Summary of Contents for KX-TCD961EB

Reviews:

Related manuals for KX-TCD961EB

Brands by name

Popular brands

Panasonic KX-TCD961EB, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD961EB

Reviews:

Related manuals for KX-TCD961EB

Brands by name

Popular brands