Panasonic KX-TCD961EB Operating Instructions Manual Download

Page: 37 / 68

Chapter 3

Cordless T

elephone (Advanced Operations)

Bell selection

All handsets

Dialling mode

Tone

Earth/time break recall

Time break recall

Pause timing

3 seconds

Call restricted handset(s)

All clear

Call restriction number(s)

All clear

Base unit password

0000

Base unit ringer volume

2 (MEDIUM)

Base unit ringer pattern

Clearing the Settings in Memory

This function enables the handset or base unit to clear the following settings at one time. They will
return to their initial settings.

Function

Initial setting

On the handset

On the base unit

Press

until “

” is displayed,

then press

Enter the handset password (p. 31).

Press

•

A confirmation tone sounds and the
display will return to the stand-by mode.

PROG

Press

then

Press

Enter the base unit password (p. 31).

Press

•

A confirmation tone sounds and the
display will return to the stand-by mode.

PROG

INT

PROG

- - - - - - - - - - - -

Base unit access

Automatic base
unit access

Key tones

Handset ringer volume

3 (MEDIUM)

Handset ringer pattern

Call waiting tone

Range warning alarm

OFF

Battery low alarm

Stand-by mode display

Base unit number

Talk mode display

Length of the call

Call prohibition

OFF

Direct call mode

OFF

Direct call number

Clear

Handset password

0000

Handset receiver volume

MEDIUM

Redial memory

All clear

Function

Initial setting

KX-TCD961EB.3(30~37) 99.9.27 7:34 PM Page 37

Summary of Contents for KX-TCD961EB





































































Search results

Summary of Contents for KX-TCD961EB

Reviews:

Related manuals for KX-TCD961EB

Brands by name

Popular brands

Panasonic KX-TCD961EB, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD961EB

Reviews:

Related manuals for KX-TCD961EB

Brands by name

Popular brands