Panasonic KX-TCD961EB Operating Instructions Manual Download

Page: 17 / 68

Chapter 1

Preparation

Press

then

Press

TWICE.

•

The current volume is displayed.
1: LOW 2: MEDIUM 3: HIGH
0: OFF

INT

PROG

Ex. MEDIUM is selected.

Selecting the Base Unit Ringer Volume/Pattern

You can program the desired base unit ringer volume and pattern.
Make sure that the power is ON (p. 14) and the unit is in the stand-by mode.

Press the desired volume level

•

Each time you press a button, the selected
volume is displayed and rings.

Press

•

A confirmation tone sounds and the display
will return to the stand-by mode.

PROG

Press

then

Press

then

•

The current ringer pattern is displayed.

Press the desired ringer pattern

•

Each time you press a button, the selected
ringer pattern is displayed and sound.

Press

•

A confirmation tone sounds and the
display will return to the stand-by mode.

PROG

INT

PROG

Ringer volume

4 levels (HIGH, MEDIUM, LOW, OFF) are
available. The factory preset is MEDIUM. When
set to OFF, the base unit will not ring.

Ringer pattern

You can program the desired base unit ringer
pattern (6 patterns). The factory preset is
pattern 1.

Ex. Patten 1 is selected.

KX-TCD961EB.1(2~22) 99.9.27 7:37 PM Page 17

Summary of Contents for KX-TCD961EB





































































Search results

Summary of Contents for KX-TCD961EB

Reviews:

Related manuals for KX-TCD961EB

Brands by name

Popular brands

Panasonic KX-TCD961EB, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD961EB

Reviews:

Related manuals for KX-TCD961EB

Brands by name

Popular brands