Panasonic KX-TCD961EB Operating Instructions Manual Download Page 20

Page: 20 / 68

Preparing the Answering System

Time and Day Adjustment

Voice Time/Day Stamp: During playback, a synthesised voice will announce the time and day that
each message was recorded.

Press

then

Press

•

“

” is displayed on the handset.

•

“

” is displayed on the base unit.

Press

•

“

” is displayed on the base unit.

•

“

Set time

” is announced.

If previously adjusted, the time/day will be
heard.

Enter the current time (hour and minute)
using a 4-digit number. (Ex. To set 9:30,
enter “0930”.)

•

The entered number is displayed on the
base unit.

Press

to select “AM” or “PM”.

Press

repeatedly to set the day.

•

The unit announces the day.

Press

•

The unit announces the time/day.
The clock starts working.

PROG

INT

PROG

If a power failure occurs, the adjusted time/day
will be erased.

•

In step 5, you cannot enter numbers greater
than 12. Do not use 24 hour clock.
(To set 13:00, enter “0100” and select “PM” by
pressing

•

The accuracy of the clock is approximately
±45 seconds a month at room temperature.

To check the time/day

Press

then

Press

•

The current time/day is heard. When
finished, press

PROG

INT

PROG

KX-TCD961EB.1(2~22) 99.9.27 7:37 PM Page 20

Summary of Contents for KX-TCD961EB





































































Search results

Summary of Contents for KX-TCD961EB

Reviews:

Related manuals for KX-TCD961EB

Brands by name

Popular brands

Panasonic KX-TCD961EB, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD961EB

Reviews:

Related manuals for KX-TCD961EB

Brands by name

Popular brands