Panasonic KX-TCD961EB Operating Instructions Manual Download

Page: 43 / 68

Chapter 4

Answering System

•

3 seconds after playback, the voice menu will start again from the beginning.

•

If you hear “

Memory is full

” after playback, erase some or all of the messages (p. 44).

All message playback.

All recorded messages are played back. At the
end of the last message, “

End of final message

” and

the remaining recording time are announced.

Press 1 to play back
all messages.
Press 2 for other
functions.

Press 1 to play back
new messages.
Press 2 for other
functions.

New message playback.

Only new messages are played back.

Press 1 to record
your message.
Press 2 for other
functions.

Please leave your message.

You can leave a personal message.
1. Talk after you hear “

Please leave your message.

”.

2. When finished, hang up.

Press 1 to erase all
messages.
Press 2 for other
functions.

Press 1 to record
your greeting.
Press 2 for other
functions.

Press 7 to record your greeting. Press 9 to end recording.

You can re-record your greeting message.

1. Press

2. Talk after the long beep.
3. When finished, press

•

Your greeting will be played back for
confirmation.

Voice Menu

The shaded boxes are voice prompts.

Press

Erase all messages.

All recorded messages (except the greeting
message) are erased.

KX-TCD961EB.4(38~46) 99.9.27 7:33 PM Page 43

Summary of Contents for KX-TCD961EB





































































Search results

Summary of Contents for KX-TCD961EB

Reviews:

Related manuals for KX-TCD961EB

Brands by name

Popular brands

Panasonic KX-TCD961EB, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD961EB

Reviews:

Related manuals for KX-TCD961EB

Brands by name

Popular brands