Panasonic KX-TCD961EB Operating Instructions Manual Download

Page: 40 / 68

Erasing Messages

The unit will announce the remaining recording time after playback, if it is less than 5 minutes. New
messages cannot be recorded when:
— “

Memory is full

” is heard.

— The number of messages displayed on the base unit flashes rapidly.
— The ANSWER ON indicator flashes rapidly.
Erase some or all of the messages. We recommend you erase unnecessary messages after each
playback.

Erasing all messages

All recorded messages, except the greeting
message, can be erased at one time.

Press

•

“

Press ERASE button again to erase all

messages.

” is heard.

Within 5 seconds, press

again.

•

A long beep sounds and “

No message

” is

heard.

•

The base unit display shows “

”.

ERASE

Erasing a specific message

Press

while the message you want

to erase is being played.

•

The unit erases the message.

•

A short beep will sound and the unit will
continue to play the next message.

ERASE

Recording a Memo Message

You can record a personal message in memory.

Press

•

A long beep sounds.

After the beep, talk clearly, about 20 cm
away from the MIC.

•

The base unit display shows the elapsed
recording time.

When finished, press

•

A beep sounds.

KX-TCD961EB.4(38~46) 99.9.27 7:33 PM Page 40

Summary of Contents for KX-TCD961EB





































































Search results

Summary of Contents for KX-TCD961EB

Reviews:

Related manuals for KX-TCD961EB

Brands by name

Popular brands

Panasonic KX-TCD961EB, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD961EB

Reviews:

Related manuals for KX-TCD961EB

Brands by name

Popular brands