Panasonic KX-TCD961EB Operating Instructions Manual Download

Page: 23 / 68

To select the receiver volume

3 levels (HIGH, MEDIUM, LOW) are available.
The factory preset is MEDIUM.

While talking, press

to select the

desired level.

•

After a few seconds, the display will return to
the length of call.

In the stand-by mode, proceed as follows.

Press .

Press

until “

” is displayed,

then press

•

The current level is displayed.

Press

to select the desired

level.

Press .

PROG

Chapter 2

Cordless T

elephone (Basic Operations)

Making Calls

To dial after confirming the
entered number

Enter a phone number.

•

The entered number is displayed.

•

If you misdial, press

. Digits are

erased from the right.

•

To cancel, press

firmly.

•

If your line has rotary or pulse service, any
access numbers entered after pressing

will not be included when dialling.

Press .

•

After a few seconds, the display will start
showing the length of the call.

To hang up, press

or place the

handset on the base unit.

•

The handset will return to the stand-by
mode.

Press .

Dial a phone number.

•

The dialled number is displayed.

•

After a few seconds, the display will start
showing the length of the call.

•

If “ ” flashes and an alarm tone sounds
after pressing

, move closer to the

base unit. Then try again.

•

You can choose whether to display the length
of the call or phone number in the talk mode
by programming (p. 36).

To hang up, press

or place the

handset on the base unit.

•

The handset will return to the stand-by
mode.

Ex. LOW is selected.

Make sure that the power is ON (p. 14).

i2345678

8888

00-00-00

Ex. LOW is selected.

KX-TCD961EB.2(23~29) 99.9.27 7:35 PM Page 23

Summary of Contents for KX-TCD961EB





































































Search results

Summary of Contents for KX-TCD961EB

Reviews:

Related manuals for KX-TCD961EB

Brands by name

Popular brands

Panasonic KX-TCD961EB, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD961EB

Reviews:

Related manuals for KX-TCD961EB

Brands by name

Popular brands