Panasonic KX-TA624 User Manual Download

Page: 76 / 234

3-16

Telephone Features

3.2

Telephone Features

Call Forwarding — Busy/No Answer

You can forward your calls to another extension when your extension is busy or if you do
not answer the call within a pre-determined time.

Setting

Programming Reference

• System Programming — Installation Manual

[202] Call Forwarding Start Time

PT and SLT

Lift the handset
or press
SP-PHONE/MONITOR.

For a PT: Press FWD/DND.
For an SLT: Dial 71.

Hang up or press
SP-PHONE/MONITOR.

Confirmation
tone and
dial tone

Dial 2. Enter the destination

extension number
(100 through 199).

Dial #.

For an SLT

For a PT

FWD/DND

extension no.

<PT Display Example>

extension number where
the call is to be forwarded

• The FWD/DND indicator light flashes red slowly.
• Single line telephone users can dial “0” instead of “#”.

FWD(B/NA) Extxxx

• You may press the flexible button assigned as

the FWD/DND button instead.

Summary of Contents for KX-TA624











































































































































































































































Search results

Summary of Contents for KX-TA624

Reviews:

Related manuals for KX-TA624

Brands by name

Popular brands

Panasonic KX-TA624, User Manual

Search results

Summary of Contents for KX-TA624

Reviews:

Related manuals for KX-TA624

Brands by name

Popular brands