Panasonic KX-TA624 User Manual Download

Page: 161 / 234

Telephone Features

3-101

3.2

Telephone Features

Condition

• If “Hold-3” is assigned in System Programming, you must dial “20” after flashing the

hookswitch.

Programming References

• System Programming — Installation Manual

[104] Hold Mode Selection
[600] Extension Group Assignment

SLT

Using Paging — Group: to a particular extension group

PT and SLT

Dial tone

Confirmation tone

Announce.

Wait for an answer.

Dial 33.

During a conversation

Hang up or press
SP-PHONE.

For a PT: Press TRANSFER.
For an SLT: Flash the hookswitch.

For an SLT

For a PT

TRANSFER

Enter a paging group
number (1 through 8).

paging group no.

• The other party is placed on hold.

• The held party and the paged extension are

connected and can start a conversation.

Summary of Contents for KX-TA624











































































































































































































































Search results

Summary of Contents for KX-TA624

Reviews:

Related manuals for KX-TA624

Brands by name

Popular brands

Panasonic KX-TA624, User Manual

Search results

Summary of Contents for KX-TA624

Reviews:

Related manuals for KX-TA624

Brands by name

Popular brands