Panasonic KX-TA624 User Manual Download

Page: 101 / 234

Telephone Features

3-41

3.2

Telephone Features

Conditions

• If the destination extension does not answer the call within a pre-determined time

(default: 30 seconds), “Transfer Recall” occurs.

• If there is no answer within thirty minutes after “Transfer Recall” starts, the line will be

disconnected.

• When the dialed extension is busy, you may access the extension by dialing “1” (Busy

Station Signaling) or “2” (Executive Busy Override) and going on-hook.

• If you want to return to the held call, press the TRANSFER button or corresponding

CO or INTERCOM button before the destination extension answers.

• When “Transfer Recall” occurs, the display will show the following:

• A flexible CO button can be assigned as a DSS button.

• To use “One-Touch Transfer”, System Programming is required.

• If you want to return to the held call, flash the hookswitch before the destination

extension answers.

• If “Hold-3” is assigned in System Programming, you must dial “20” after flashing the

hookswitch.

Programming References

• Station Programming (Section 2)

Flexible Button Assignment — Direct Station Selection (DSS) Button

• System Programming — Installation Manual

[005] One-Touch Transfer Using a DSS Button
[104] Hold Mode Selection
[201] Transfer Recall Time

Feature References

Call Transfer, Screened – to Extension (

→

See the Installation Manual.)

Call Transfer, Unscreened – to Extension (

→

See the Installation Manual.)

One-Touch Transfer Using a DSS Button (

→

See the Installation Manual.)

SLT

RCL: Ext 101

Summary of Contents for KX-TA624











































































































































































































































Search results

Summary of Contents for KX-TA624

Reviews:

Related manuals for KX-TA624

Brands by name

Popular brands

Panasonic KX-TA624, User Manual

Search results

Summary of Contents for KX-TA624

Reviews:

Related manuals for KX-TA624

Brands by name

Popular brands