Panasonic KX-FC231NZ, Operating Instructions Manual

Page: 84 / 114

11. Multi-unit Operation
82
4
Select the desired base unit number, or
“
Auto
” , then press
{>}
.
L
The handset starts searching for the base
unit.
11.2.4 Cancelling a handset
A handset can cancel its own registration (or the
registration of another handset) that is stored in
the base unit. This will allow the base unit to
forget the handset.
1
Press
{j
/OK
}
.
2
Select “
Base Unit Setup
” , then press
{>}
.
3
Enter “
0000
” (default base unit PIN).
L
If you changed the PIN, enter it (page 80).
4
Enter “
335
” .
5
Select “
Cancel Handset
” , then press
{>}
.
L
The numbers of all handsets registered to
the base unit are displayed.
6
Select the handset(s) you want to cancel, by
pressing the desired handset number.
L
The selected handset number(s) will
flash.
L
To cancel a selected handset number,
press the number again. The number will
stop flashing.
7
Press
{j
/OK
}
.
8
Select “
Yes
” , then press
{>}
.
11.2.5 Cancelling a base unit
A handset can cancel a base unit that it is
registered to. This allows the handset to forget
the base unit.
1
Press
{j
/OK
}
.
2
Select “
Handset Setup
” , then press
{>}
.
3
Select “
Registration
” , then press
{>}
.
4
Enter “
335
” .
5
Select “
Cancel Base
” , then press
{>}
.
6
Enter “
0000
” (default handset PIN).
L
If you changed the PIN, enter it (page 77).
7
Select the base unit(s) you want to cancel, by
pressing the desired base unit number.
L
The selected base unit number(s) will
flash.
L
To cancel a selected base unit number,
press the number again. The number will
stop flashing.
8
Press
{j
/OK
}
.
9
Select “
Yes
” , then press
{>}
.
10
Press
{ih}
.
Note:
L
To register the handset to another base unit
or to the same base unit again, see manual
registration on page 81.
11.2.6 Increasing the range of
the base unit
You can increase the range of the base unit by
using a DECT repeater. Please use only
Panasonic DECT repeater. See page 11 for
accessory information.
Important:
L
Before registering the repeater to this
base unit, you must turn the repeater
mode ON.
Setting the repeater mode
1. Press
{j
/OK
}
.
2. Select “
Base Unit Setup
” , then press
{>}
.
3. Enter “
0000
” (default base unit PIN).
L
If you changed the PIN, enter it (page 80).
4. Select “
Other Options
” , then press
{>}
.
5. Select “
Repeater Mode
” , then press
{>}
.
6. Select “
On
” or “
Off
” (default), then press
{>}
.
7. Press
{ih}
.
Note:
L
After turning repeater mode ON/OFF, you will
not be able to make or receive calls for a few
moments.
11.3 Handset locator
Using this feature, you can locate the handset if
it has been misplaced.
L
Keep the front cover page open for button
locations.
1
Press
{
LOCATOR
}
.
L
The base unit will page the handset for
about 1 minute.
2
To stop paging, press
{
LOCATOR
}
on the
base unit or
{ih}
on the handset.
Note:
L
This feature is not available while using
{
DIGITAL SP-PHONE
}
.
FC235AL-PFQX2248ZA_en.book Page 82 Monday, June 20, 2005 2:19 PM