Panasonic GT01 User Manual Download Page 61

Page: 61 / 206

2-21



Setting of destination (PLC side)

IP address: Specify the IP address of the GT to be connected in decimal.
Port No.: Set it within the range of 1 to 32767 in decimal. (Default: 9094)

Specify the same setting as the one of GT.



Communication time out:

Set the time-out period after connection establishment for every

communication within the range of 1 to 950 seconds. (Default: 15) (it is not
linked to this setting until a connection is established)



Connection time out:

Set the time-out period until connection establishment within the range of 1
to 180 seconds. (Default: 60)

Setting with IP search tool (Config WD. exe)

The settings of the GT can be specified with the IP address search tool of Configurator WD (Ver.1.11 or
later).
The IP search tool (Config WD. exe) can be downloaded for free from our website
URL:

http://industrial.panasonic.com/ac/e/dl_center/software/

(User registration is required.: Free of charge)

Summary of Contents for GT01















































































































































































































Search results

Summary of Contents for GT01

Reviews:

Related manuals for GT01

Brands by name

Popular brands

Panasonic GT01, User Manual

Search results

Summary of Contents for GT01

Reviews:

Related manuals for GT01

Brands by name

Popular brands