Panasonic GT01 User Manual Download Page 166

Page: 166 / 206

6-26

6.7 GT12

6.7.1 General Specifications (GT12)

Item

Specifications

Rated voltage

24 V DC

Operating voltage range

21.6 to 26.4 V DC

Power consumption

1.7 W or less (70 mA or less)

Insulation method of
power supply part

Transformer insulation

Note1)

Ambient temperature

0 to +50



Ambient humidity

20 to 85% RH (at 25



C), non-condensing

Storage temperature

-20 to +60



Storage humidity

10 to 85% RH (at 25



C), non-condensing

Breakdown voltage

Note1)

Between [power supply terminals (+ and

– terminals)] and [function earth

terminal]
500 V AC for 1 minute, Cutoff current 10mA (in initial status)

Insulation resistance

Note1)

Between [power supply terminals (+ and

– terminals)] and [function earth

terminal]
100 M



or more, 500 V DC, measured with megohmmeter (in initial

status)

Vibration resistance

5 to 9 Hz amplitude 3.5 mm,
9 to 150 Hz acceleration 9.8 m/s

10 sweeps each in X, Y and Z directions (1 octave/min)

Shock resistance

147 m/s

, 3 times on 3 axes

EC Directive applicable

EMC Directive: EN61131-2

Noise immunity

1000 V [P-P] or more, Pulse width 50 ns, 1



s between power supply

terminals (based on in-house measurements)

Note2)

Protective construction

IP67 (Initial value, evaluated by us)
Dustproof and waterproof from front panel only (packing used on panel
contact surface)

Note3)

Weight

Approx. 240 g

Note1) Not isolated between the USB port, COM. port and the internal digital circuit.
Note2) When using our exclusive cable.
Note3) When installing the unit again, replace the water-proof packing.

Summary of Contents for GT01















































































































































































































Search results

Summary of Contents for GT01

Reviews:

Panasonic GT01, User Manual, Page: 166 / 206

Search results

Summary of Contents for GT01

Reviews: