Panasonic GT01 User Manual Download Page 69

Page: 69 / 206

3-7

3.1.8 GT05 / GT32 / GT32-R / GT32-E Installation Method

Secure the GT32 to the installation panel using the two fittings and four screws provided with the unit.

1. Place the GT main unit in the installation panel.
2. Insert the fittings into the grooves provided in the GT main unit, and tighten the screws to

secure the GT main unit to the installation panel.

GT05 / GT32
The screw tightening torque should be 0.1 to 0.25 N· m, and tighten them uniformly.

GT32-R / GT32-E
The screw tightening torque should be 0.2 to 0.3 N· m, and tighten them uniformly.

Tightening the screws too hard can cause deformation of the front panel, so that the touch switches will
not function properly. Install the GT within the above range.

Summary of Contents for GT01















































































































































































































Search results

Summary of Contents for GT01

Reviews:

Related manuals for GT01

Brands by name

Popular brands

Panasonic GT01, User Manual

Search results

Summary of Contents for GT01

Reviews:

Related manuals for GT01

Brands by name

Popular brands