Panasonic GT01 User Manual Download Page 66 | Manualshive

Page: 66 / 206

background image

3-4

3.1.2 Restriction According to Mounting Directions

If the unit is being installed in a horizontal orientation, or our Programmer II and C-NET adaptor are
being connected to the TOOL port, note that the ambient usage temperature should be as below.

Model

name

Condition

Ambient

temperature

GT11

Vertically installed

0 to 45



C

Programmer II
C-NET adapter

GT21

Horizontally installed
Programmer II

C-NET adapter

GT32

Horizontally installed

0 to 40



C

GT03-E
GT32-E

Horizontally installed

-20 to 55



C

Vertically installed

Note) When installing the unit aslant, the restriction is the same as the one when installing horizontally.

3.1.3 Installation Space

Applicable panel thickness

A panel with a thickness of 1.0 to 5.0 mm should be used.
Use a panel that is strong enough not to be warped.

Clearance when the GT is installed

When installing other parts to the panel or wiring cables to it, provide a clearance around the panel to
prevent cables from being damaged and to facilitate the installation work.

When performing installation work, make sure to observe the following.



Never obstruct the slits of the GT unit.



Make sure that no foreign matter enters inside through the slits. If conductive foreign matter enters

inside, it may malfunction or product failure.

Model name

Clearance

Clearance on the surface

to connect the screen

transfer cable

Clearance on the

mounting surface when

using a SD memory card

GT01
GT11
GT21

30 mm or more

(50 mm or more

recommended)

20 mm

-

GT02L

GT03M-E

60 mm

-

GT02
GT05

GT03T-E

GT12
GT32

GT32-R
GT32-E

60 mm

40 mm or more

* It should be 40 mm or more when using a SD memory card.

«
...
64
65
66
67
68
...
»

Summary of Contents for GT01















































































































































































































Reviews:

No comments

Related manuals for GT01

Brand: Handicare Pages: 56

Brand: Aalborg Pages: 15

Brand: Aalborg Pages: 48

C-NaviGator III

Brand: C-Nav Pages: 20

Brand: Samson Pages: 52

Brand: Samson Pages: 32

Brand: Danfoss Pages: 59

Brand: Samson Pages: 73

Brand: Quectel Pages: 95

Brand: ICAS Pages: 51

Brand: Icar Pages: 40

Brand: Icar Pages: 86

Brand: Icar Pages: 39

Brand: IBP Pages: 12

Brand: OES Pages: 3

Wireless Blade FX Controller for Wii

Brand: Datel Pages: 2

Brand: TeleMann Pages: 4

Brand: asalvo baby Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands