Panasonic GT01 User Manual Download Page 84 | Manualshive

Page: 84 / 206

background image

3-22

3.6.4 Dead Battery Mark

If the battery voltage drops too low, the battery mark is displayed at the bottom right of the GT screen.

When the battery voltage drops

It can be specified in the GTWIN configuration settings, whether or not the dead battery mark is
displayed .

Note:

If the battery voltage drops too low, the BAT LOW flag of the basic communication area map goes on. If
the battery has run down completely, the BAT flag of the basic communication area map goes on.
Please be aware that the BAT flag goes on the first time that the power supply is turned on after the unit
is purchased.

* The BAT and BAT LOW flags in the basic communication area map activate in the both cases that the

battery error display is set to

“On” and “Off”.

3.6.5 Time for Replacement of Battery

When replacing the backup battery, turn on electricity for the time for energization, and replace the
battery with a new one within one minute after turning off the power supply.
If the battery is not replaced within the time for replacement, the saved data will be lost.

Time for energization

Time for replacement

1 min. or more (10 min. or more for GT32)

Within 1 min.

3.6.6 Replacement of Front Panel Protective Sheet

About the front panel protective sheet

Use the separately-sold protective sheets to protect the touch panel surface and to keep it clean.

Replacing the front panel protective sheet (For GT01 (except GT01R) and GT11)

Follow the steps below to replace the sheet:

1. Peel off the seal from the provided protector sheet and attach it to the unit.

Take out one of the replacement front panel protective sheets and peel off the seal with the shiny side.
When attaching the sheet, align the adhesive edges with the front of the GT. Finish by peeling off the
thin film attached to the top of the front panel protective sheet.

«
...
82
83
84
85
86
...
»

Summary of Contents for GT01















































































































































































































Reviews:

No comments

Related manuals for GT01

Brand: Ohsung Electronics Pages: 18

Brand: XGAMING Pages: 9

HomeTec Pro CFF3000

Brand: Abus Pages: 13

Brand: NAVITAS Pages: 7

Brand: Abus Pages: 2

Brand: Baader Planetarium Pages: 7

Brand: Beaphar Pages: 2

iBox Hub 25020180

Brand: Hans Grohe Pages: 36

Brand: M-Audio Pages: 26

Brand: M Climate Pages: 12

Brand: Uniden Pages: 28

Brand: UniFocus Pages: 23

Brand: UniFocus Pages: 6

Brand: UniPOS Pages: 51

Brand: Unipulse Pages: 126

Brand: YachtSafe Pages: 3

Brand: Apex Toys Pages: 7

NuMicro M252 Series

Brand: Nuvoton Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands