Panasonic GT01 User Manual Download Page 179

Page: 179 / 206

6-39

6.10 GT32-R

6.10.1 General Specifications (GT32-R)

Item

Specifications

GT32M-R

GT32T-R

Rated voltage

24 V DC

Operating voltage range

21.6 to 26.4 V DC

Power consumption

4.8 W or less (200 mA or less)

7.2 W or less (300 mA or less)

Insulation method of
power supply part

Transformer insulation

Ambient temperature

0 to +50



Ambient humidity

20 to 85% RH (at 25



C), non-condensing

Storage temperature

-20 to +60



Storage humidity

10 to 85% RH (at 25



C), non-condensing

Breakdown voltage

Note1)

Between [power supply terminals] and [case]
500 V AC for 1 minute, Cutoff current 10mA (at default setting)

Insulation resistance

Between [power supply terminals] and [case]
100 M



or more, 500 V DC, measured with megohmmeter (at default

setting)

Vibration resistance

5 to 8.4 Hz half amplitude 3.5 mm
8.4 to 150 Hz acceleration 9.8 m/s2,
10 sweeps each in X, Y and Z directions (1 octave/min)

Shock resistance

147 m/s

, 4 times on 3 axes

EC Directive applicable

EN61131-2 (EMC Directive)

Noise immunity

1000 V [P-P] or more, Pulse width 50 ns, 1



s between power supply

terminals (based on in-house measurements)

Note2)

Electrostatic discharge
resistance

6kV
(Contact Discharge, EN61000-4-2 Level 3)

Protective construction

IP67 (Initial value, evaluated by us)
Dustproof and drip-proof from front panel only (packing used on panel
contact surface)

Note3)

Weight

Approx. 470 g

Note1) Not isolated between the USB port, COM port and the internal digital circuit.
Note2) When using our exclusive cable.
Note3) When reattaching, replace waterproof packing.

Summary of Contents for GT01















































































































































































































Search results

Summary of Contents for GT01

Reviews:

Related manuals for GT01

Brands by name

Popular brands

Panasonic GT01, User Manual

Search results

Summary of Contents for GT01

Reviews:

Related manuals for GT01

Brands by name

Popular brands