Panasonic DMRE500H - DVD RECORDER DECK, Operating Instructions Manual

Page: 51 / 160

51
RQT7751
T
ra
n
s
fe
r (
D
ubbing)
Recording from a video cassette recorder
e.g., Connecting other video equipment to the AV3 or DV input
terminals
≥
Turn off the unit and other video equipment before connecting.
If the audio output of the other equipment is monaural, connect to L/MONO.
§
The S-VIDEO terminal achieves a more vivid picture than the
VIDEO terminal.
DV automatic recording (DV AUTO REC) (
➡
page 52)
When recording from the unit’s DV terminal
Select the type of audio recording from “Audio Mode for DV Input” in
the SETUP menu (
➡
page 64).
[HDD] [RAM] [DVD-R]
Preparation
≥
Connect a video cassette recorder to this unit’s input terminals.
≥
Press [HDD] or [DVD] to select the recording drive.
≥
To adjust the audio recording level (
➡
below)
≥
When recording bilingual programmes
[HDD] [RAM]
When both M 1 and M 2 is selected on the connected equipment,
you can select the audio type in playback.
(
[HDD]
When simultaneously recording by MPEG4 format, select
either M 1 or M 2 on the connected equipment)
[DVD-R]
Select either M 1 or M 2 on the connected equipment.
≥
When the output signal from the external equipment is NTSC,
change the “TV System” to “NTSC” in the SETUP menu (
➡
page 67).
≥
To reduce noise in input from a video cassette recorder, set “AV-in
NR” to “On” in the SETUP menu (
➡
page 63).
1
While stopped
Press [INPUT SELECT] to select the
input channel for the equipment you
have connected.
e.g., If you have connected to AV3 input terminals, select “AV3”.
2
Press [REC MODE] to select the
recording mode.
3
Start play on the other equipment.
4
Press [
¥
REC].
Recording starts.
To skip unwanted parts
Press [
;
] to pause recording. (Press again to restart recording.)
To stop recording
Press [
∫
].
To record programmes to fill up the remaining space on the disc
➡
page 26, Flexible Recording
∫
To adjust the audio recording level
1
Before recording commences, press and hold [AUDIO] for
more than 3 seconds.
2 Press [
3
,
4
] to select “L/R”.
To individually adjust a level press [
3
,
4
] to select “L” (left) or “R”
(right).
≥
If “L” (left) and “R” (right) cannot be selected with [
3
,
4
], press
[AUDIO] to switch the audio.
3 Press [
2
,
1
] to adjust the audio recording level and press
[ENTER].
≥
Set the level to neutral again after finishing recording as other
recordings will also be affected.
≥
If the recording level is too high the audio will be distorted. Set it so
the audio level meter is not shaking. (Maximum –10 dB to –5 dB is
an appropriate level)
≥
The DV input is unaffected.
VOLUME
CH
DIRECT TV REC
DVD
TV
AV
1 2 3
4 5 6
7 8
0
9
MANUAL SKIP
ShowView
CH
CANCEL INPUT SELECT
SKIP
STOP PAUSE PLAY/x1.3
SLOW/SEARCH
FUNCTIONS
ENTER
DIRECT NAVIGATOR
TOP MENU
RETURN SUB MENU
CREATE
CHAPTER
TIMER
EXT LINK
PROG/CHECK
REC MODE ERASE REC
AUDIO
TIME SLIP STATUS DISPLAY
F
A B C
DUBBING
HDD DVD SD/PC
3
,
4
,
2
,
1
ENTER
FUNCTIONS
AUDIO
REC MODE
HDD, DVD
¥
REC
INPUT SELECT
∫
;
HDD DVD SD PC
HDD DVD
TIME SLIP DRIVE SELECT /x1.3
OPEN/CLOSE
PC CARD
EJECT
SD CARD
DV IN AUDIO IN VIDEO IN S-VIDEO IN
AV3
L/MONO R
DV IN
L/MONO - AUDIO IN - R VIDEO IN S-VIDEO IN
Audio/
Video cable S-Video
cable
§
Other video
equipment
Yellow White Red
This unit
DV cable
(IEEE 1394, 4-pin)
Manual recording
Almost all videos and DVD software on sale have been
treated to prevent illegal copying. Any software that has
been so treated cannot be recorded using this unit.
Audio REC Level
R
L
R
L/R
L
30 20 15 10 5 0 OVER
0
0
-
¶
CH SELECT
ADJUST
RETURN
ENTER
51
7551-EN.book 51 ページ ２００４年８月２６日 木曜日 午後４時３４分