Panasonic AW-UE150KE Operating Instructions Manual Download

Page: 62 / 174

IP output

• When [IP] of [Tracking Data Output] on the [System 2/2] screen is

set to [On], the tracking data for Pan/Tilt/Zoom or other information is

synchronized with the Genlock signal and outputs UDP packets via IP.

• Outputs simultaneously up to four clients (IP addresses) that have

been specified on the designated web screen (→ page 128).

• The tracking data is output in a format conforming to the free-d

protocol. The output specification (mode, command type, advanced

stored data) of this unit is equivalent to serial (RS-422) output.

<NOTE>

• When forwarding to more than one client, the timing of transmitting

the UDP packet to the second and subsequent client will always be

delayed relative to the Genlock signal.

(Approximately 200 to 300 μs delay will occur for each client. The

latency may be increased depending on the system status or the

network environment of the unit.)

• When [IP] is [On], video transmission via IP may be delayed or the

video may suffer frame loss.

We recommend setting [IP] to [Off] to avoid the delay or frame loss

due to the video transmission via IP.

• In the following cases, the tracking data output may be delayed or the

value may not be updated.

- When performing video transmission via IP (M-JPEG/H.264/H.265/

RTMP/RTMPS/NDI|HX/SRT)

- When opening the web screen (live screen [Live] or the web setting

screen [Setup])

- While viewing the OSD menu

- While recalling the preset value during an ongoing preset recall

- When executing AWB/ABB

- When a red or a green tally signal input has been changed between

Off and On

- When deleting a preset memory

- When an output image is flipped (turned upside down or left-right

reversed)

- After switching [Scene]

- After switching [Iris Mode]

- After switching [Super Gain]

- After switching [White Balance Mode]

- After switching each item of [Color TEMP. Setting]

- After switching [Gamma Mode]

- After switching [Matrix Type]

- After switching [Focus Mode]

- After switching [Zoom Mode]

- After switching [Max Digital Zoom]

- After switching [Digital Extender]

- After switching between [Fan1] and [Fan2]

- After switching [OSD Mix]

- After switching [Tally]

- After moving the crop frame of [UHD Crop]

- After switching [Install Position]

- After switching [Preset Speed Unit]

- When executing [Initialize] of [Maintenance]

Camera menu items (continued)

Summary of Contents for AW-UE150KE















































































































































































Search results

Summary of Contents for AW-UE150KE

Reviews:

Related manuals for AW-UE150KE

Brands by name

Popular brands

Panasonic AW-UE150KE, Operating Instructions Manual

Search results

Summary of Contents for AW-UE150KE

Reviews:

Related manuals for AW-UE150KE

Brands by name

Popular brands