– 24 –
Chapter 2 Description of Parts — Rear side
30
<TRUNK> terminal
This is an input/output terminal for the CCU trunk data (RS-422
×
2 or RS-232C
×
2).
Set this in [MAIN MENU]
→
[IN/OUT SELECT]
→
[TRUNK1]/[TRUNK2].
31
<G/L IN/PROMPTER OUT> terminal
This is the input terminal for genlock signals. The prompter video input from the CCU is output from this terminal.
When the camera is used standalone, this terminal works as the genlock input. When connecting with the CCU, this terminal works as the prompter
output.
@
@
NOTE
t
Genlock can be applied to following signals when [MAIN MENU]
→
[SYSTEM MODE]
→
[FORMAT] is set to [1080/23.98p].
-
HD-Y signal of 1080/23.98p or 1080/23.98PsF
-
Composite signal
t
Genlock can be applied to following signals when it is set to anything other than to [1080/23.98p].
-
HD-Y signal of 1080/59.94i or 1080/50i
-
Composite signal
32
<INTERCOM1> terminal
Used to connect the intercom or headset plug.
33
Back tally lamp
Lights up when the tally signal is supplied.
R tally signal:
Lit in red
G tally signal:
Lit in green
R and G tally signals at the same time:
Lit in red
34 Back tally lamp selector switch
Used to switch the back tally lamp to on/off.
35
Rear viewfinder terminal
Used to connect the 9-inch LCD viewfinder AK-HVF100G.
This D-sub connector is used for the viewfinder interface.
@
@
NOTE
t
AK-HVF70G can also be connected to this terminal.
36
<EARPHONE> terminal
Used to connect the plug of a set of earphones.
Configures the audio output from [MAIN MENU]
→
[INTERCOM SETTING]
→
[EAR PHONES SETTING]
→
[LCH OUTPUT SELECT]/[RCH
OUTPUT SELECT].
37 <INTERCOM2> terminal
Used to connect the intercom or headset plug.
38
<HD SDI1> terminal (BNC)
[CAM]:
Outputs camera images.
[HD PROMPT]:
Outputs HD prompter video images.
Configure the output images in [MAIN MENU]
→
[IN/OUT SELECT]
→
[HD-SDI1 OUT].
@
@
NOTE
t
Use a cable that is 5C-FB or above.
t
[HD PROMPT] can be selected only when the camera is connected to the CCU.
39 <HD SDI2> terminal (BNC)
[CAM]:
Outputs camera images.
[VF]:
Outputs viewfinder images.
[RET]:
Outputs return images.
[RET1]/[RET2]/[RET3]/[RET4]:
Outputs the selected images.
Configure the output images in [MAIN MENU]
→
[IN/OUT SELECT]
→
[HD-SDI2 OUT].
@
@
NOTE
t
Use a cable that is 5C-FB or above.
t
[RET] and [RET1]/[RET2]/[RET3]/[RET4] can be selected only when the camera is connected to the CCU.
40 <AUX> terminal
This is the external device connecting terminal.
[PMT2 OUT]:
Outputs prompter 2 video images.
[HD TRUNK]:
HD trunk input
Set this from [MAIN MENU]
→
[IN/OUT SELECT]
→
[AUX I/O].
@
@
NOTE
t
Use a cable that is 5C-FB or above.
t
The HD trunk input cannot be selected when [MAIN MENU]
→
[SYSTEM MODE]
→
[FORMAT] is set to [1080/50p-200fps] or
[1080/59.94p-240fps].
t
If the HD trunk input is selected, only 1080/59.94i input is available when an input signal is 59.94 Hz; only 1080/50i input is available when an input
signal is 50 Hz.
