Ozito PMT-004 Instruction Manual Download Page 36

Page: 36 / 40

TROUBLESHOOTING

Fault

Possible cause

Remedy

The engine does not
start

Correct starting
procedure not followed

Follow the instructions for starting
the engine

Sooted or damp spark
plug

Clean the spark plug or replace it
with a new one

Incorrect carburettor
setting

Contact an authorized customer
service outlet.

The equipment
starts but does not
develop its full
power.

Incorrect choke lever
setting

Set the choke to “

“

Soiled oil filter

Clean the oil filter

Incorrect carburettor
setting.

Contact an authorized customer
service outlet.

The engine does not
run smoothly

Incorrect electrode gap
on the spark plug

Clean the spark plug and adjust the
electrode gap, or fit a new spark plug

Incorrect carburettor
setting

Contact an authorized customer
service outlet.

Engine smokes
excessively

Incorrect fuel mix

Use the correct fuel mix (see fuel
mixing table)

Incorrect carburettor
setting

Contact an authorized customer
service outlet.

Pruner chain dry

No oil in the tank

Fill up with oil

Oil tank cap breather
blocked

Clean the oil tank cap

Oil outlet blocked

Clean the oil outlet

Chain/guide bar hot

No oil in the tank

Fill up with oil

Oil tank cap breather
blocked

Clean the oil tank cap

Oil outlet blocked

Clean the oil outlet

Blunt chain

Re-sharpen or replace chain

Chain is over tensioned

Check the chain tension

Pruner juddering,
vibrating or not
sawing properly

Chain tension too loose

Adjust the chain tension

Blunt chain

Re-sharpen or replace chain

Worn chain

Replace the chain

Chain teeth pointing in
wrong direction

Reinstall the saw chain with the teeth
facing in the correct direction

Summary of Contents for PMT-004









































Search results

Summary of Contents for PMT-004

Reviews:

Related manuals for PMT-004

Brands by name

Popular brands

Ozito PMT-004, Instruction Manual

Search results

Summary of Contents for PMT-004

Reviews:

Related manuals for PMT-004

Brands by name

Popular brands